Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

In this system, the signals of the duplex type stop light switch (STP and ST1-) are used to judge whether the brake system is abnormal. When signals that indicate depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch.

HINT:
Normal conditions are shown in the table below.

Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF


DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more:
(1 trip detection logic)
(a) Ignition switch is ON
(b) Brake pedal is released
(c) STP signal is OFF when ST1- signal is OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM


A154326E03


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF STOP LIGHT
  1. Check if the stop lights turn ON and OFF when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON and OFF normally.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2.CHECK STP SIGNAL


    A080995E14
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

  1. Read the value.

    OK:
    Brake Pedal
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Brake Pedal
    Specified Condition
    ST1- (E6-14) - E1 (E7-7)
    Depressed
    Below 1.5 V
    ST1- (E6-14) - E1 (E7-7)
    Released
    7.5 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


3.CHECK STOP LIGHT SWITCH ASSEMBLY


    A072924E26
  1. Remove the stop light switch.

  1. Measure the resistance of the stop light switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin not pushed
    10 kΩ or higher
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)


    A099860E12
  1. Disconnect the S14 stop light switch connector.

  1. Disconnect the E6 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    S14-1 - STP (E6-15)
    Below 1 Ω
    S14-4 - ST1- (E6-14)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    S14-1 or STP (E6-15) - Body ground
    10 kΩ or higher
    S14-4 or ST1- (E6-14) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)