Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0405    Exhaust Gas Recirculation Sensor "A" Circuit Low

DTC    P0406    Exhaust Gas Recirculation Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

DTC No.
DTC Detection Condition
Trouble Area
P0405
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM
P0406
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

MONITOR DESCRIPTION

When output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM


A154317E03


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)


    A148945E03
  1. Disconnect the E2 EGR valve position sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC (E2-1) - E2 (E2-2)
    4.5 to 5.5 V



NG
Go to step 3
OK


2.INSPECT EGR VALVE POSITION SENSOR
A148947E01
  1. Disconnect the EGR valve position sensor connector.

  1. Measure the resistance of the EGR valve position sensor.

    Standard resistance:

    Tester Connection
    EGR Valve Condition
    Condition
    Specified Condition
    VC (1)- E2 (2)
    -
    20°C (68°F)
    3.5 to 6.5 kΩ
    EGLS (3) - E2 (2)
    Fully opened
    20°C (68°F)
    3.9 kΩ
    EGLS (3) - E2 (2)
    Fully closed
    20°C (68°F)
    1.0 kΩ



NG
REPLACE EGR VALVE POSITION SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)


    A155126E03
  1. Disconnect the E2 EGR valve position sensor connector.

  1. Disconnect the E7 and E8 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VC (E2-1) - VC (E8-18)
    Below 1 Ω
    EGLS (E2-3) - EGLS (E7-33)
    Below 1 Ω
    E2 (E2-2) - E2 (E8-28)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    EGLS (E2-3) or EGLS (E7-33) - Body ground
    10 kΩ or higher
    VC (E2-1) or VC (E8-18) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)