Home › SERVICE SPECIFICATIONS › SERVICE SPECIFICATIONS › 1KD-FTV STARTING

1KD-FTV STARTING > SERVICE DATA



for 2.2 kW Type bosch made
Starter
No-load characteristics current
123A or less at 11.5 V
Starter armature assembly
Maximum circle runout
0.04 mm (0.0016 in.)
Standard circle runout
0.02 mm (0.0008 in.)
Standard commutator diameter
32.2 mm (1.2783 in.)
Minimum commutator diameter
31.1 mm (1.2347 in.)
Standard undercut depth
0.9 mm (0.0354 in.)
Minimum undercut depth
0.4 mm (0.0157 in.)
Segments
Below 1.7 Ω
Segment - Coil core
10 kΩ or higher
Brush
Standard length
14.0 mm (0.5558 in.)
Minimum length
9.0 mm (0.3543 in. )
Tester connection
A-B
10 kΩ or higher
Tester connection
A-C
10 kΩ or higher
Tester connection
A-D
Below 1 Ω
Tester connection
B-C
Below 1 Ω
Tester connection
B-D
10 kΩ or higher
Tester connection
C-D
10 kΩ or higher
Magnet starter switch
Terminal 50 - Terminal C
Below 1 Ω
Terminal 50 - Body
Below 2 Ω
for 2.2 kW Type denso made
Starter
No-load characteristics current
120 A or less at 11.5 V
Starter armature
Maximum circle runout
0.05 mm (0.0020 in.)
Standard commutator diameter
35.5 mm (1.378 in.)
Minimum commutator diameter
34.0 mm (1.339 in.)
Standard undercut depth
0.7 mm (0.028 in.)
Minimum undercut depth
0.2 mm (0.008 in.)
Segments
Below 1 Ω
Segment - Coil core
10 kΩ or higher
Brush length
Standard length
16.5 mm (0.650 in.)
Minimum length
9.0 mm (0.354 in. )
Brush spring
Standard spring installed load
26.5 to 32.3 N
(2.7 to 3.3 kgf*cm, 5.9 to 7.3 in.*lbf)
Minimum spring installed load
17.6 N
(1.8 kgf*cm, 4.0 in.*lbf)
Brush holder
Positive brush - Negative brush
10 kΩ or higher
Magnet starter switch
Terminal 50 - Terminal C
Below 1 Ω
Terminal 50 - Body
Below 2 Ω
for 2.7 kW Type
Starter
No-load characteristics current
180 A or less at 11 V
Starter armature assembly
Maximum circle runout
0.05 mm (0.0020 in.)
Standard commutator diameter
36.0 mm (1.417 in.)
Minimum commutator diameter
35.0 mm (1.378 in.)
Standard undercut depth
0.7 mm (0.028 in.)
Minimum undercut depth
0.2 mm (0.008 in.)
Segments
Below 1 Ω
Segment - Coil core
10 kΩ or higher
Brush length
Standard length
20.5 mm (0.814 in.)
Minimum length
11.0 mm (0.433 in.)
Brush spring
Standard spring installed load
34.3 to 42.1N
(3.5 to 4.3 kgf*cm, 7.7 to 9.5 in.*lbf)
Minimum spring installed load
18.6 N
(1.9 kgf*cm, 4.2 in.*lbf)
Starter yoke
Lead wire - Field coil brush lead
Below 1 Ω
Lead wire - Starter yoke body
10 kΩ or higher
Brush holder
Positive brush - Negative brush
10 kΩ or higher
Magnet starter switch
Terminal 50 - Terminal C
Below 1 Ω
Terminal 50 - Body
Below 2 Ω
Glow plug
Resistance
Approx. 0.95 Ω
ECT sensor
Resistance
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ
Starter relay
Specified resistance
3-5
10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminal 1 and 2)
Glow relay
Specified resistance
3-5
10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminal 1 and 2)
Ignition switch
Tester connection
-
Switch condition
Lock
Specified condition
10 kΩ or higher
Tester connection
2 (ACC) - 4 (AM1)
Switch condition
ACC
Specified condition
Below 1 Ω
Tester connection
1 (IG1) - 4 (AM1)
2 (ACC) - 4 (AM1)
5 (AM2) - 6 (IG2)
Switch condition
ON
Specified condition
Below 1 Ω
Tester connection
1 (IG1) - 4 (AM1)
3 (ST1) - 4 (AM1)
5 (AM2) - 6 (IG2)
5 (AM2) - 7 (ST2)
Switch condition
START
Specified condition
Below 1 Ω