Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    12    Ambient Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The sensor connected to the accessory meter detects fluctuations in the ambient temperature. This information is used for controlling the interior temperature. The accessory meter detects the resistance of the thermistor (A/C ambient temperature sensor) and sends this information to the air conditioning amplifier.

DTC Code
Detection Item
Trouble Area
12
Open or short in ambient temperature sensor circuit
  1. Thermistor assembly (A/C ambient temperature sensor)
  2. Harness or connector
  3. Accessory meter assembly
  4. Air conditioning amplifier assembly

WIRING DIAGRAM


E171025E01


INSPECTION PROCEDURE

1.CHECK ACCESSORY METER ASSEMBLY


    E113424
  1. Check the difference between the ambient temperature value displayed on the accessory meter and the actual ambient temperature.

    OK:
    The ambient temperature displayed on the accessory meter and the actual ambient temperature are almost the same.

    HINT:
    The temperature displayed on the accessory meter and the actual temperature detected by the thermistor may differ when the ambient temperature changes significantly (for example, when the vehicle is entering/exiting tunnels, or the vehicle speed or wind direction changes).



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - AIR CONDITIONING AMPLIFIER)


    E170947E04
  1. Disconnect the A27 meter connector.

  1. Disconnect the A37 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-9 (DATA) - A37-18 (TAMO)
    Always
    Below 1 Ω
    A27-9 (DATA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.CHECK ACCESSORY METER ASSEMBLY (TH+, DATA VOLTAGE)


    E170944E02
  1. Remove the accessory meter with its connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-3 (TH+) - A27-2 (SG)
    Ignition switch ON
    Ambient temperature: 20 to 30°C (68 to 86°F)
    1.0 to 1.6 V
    Ignition switch ON
    Ambient temperature: 30 to 50°C (86 to 122°F)
    0.6 to 1.0 V
    A27-9 (DATA) - Body ground
    Ignition switch ON
    Ambient temperature changes
    Pulse generation

    HINT:
    As the temperature increases, the voltage decreases.

    Result 
    Result
    Proceed to
    OK
    (Checking from the PROBLEM SYMPTOMS TABLE)
    A
    OK
    (Checking from the DTC)
    B
    NG
    C



B
Go to step 4

C
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - AIR CONDITIONING AMPLIFIER)


    E170947E05
  1. Disconnect the A27 meter connector.

  1. Disconnect the A37 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-9 (DATA) - A37-18 (TAMO)
    Always
    Below 1 Ω
    A27-9 (DATA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

5.INSPECT THERMISTOR ASSEMBLY (A/C AMBIENT TEMPERATURE SENSOR)


    E170945E01
  1. Remove the thermistor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    10°C (50°F)
    3.00 to 3.73 kΩ
    15°C (59°F)
    2.45 to 2.88 kΩ
    20°C (68°F)
    1.95 to 2.30 kΩ
    25°C (77°F)
    1.60 to 1.80 kΩ
    30°C (86°F)
    1.28 to 1.47 kΩ
    35°C (95°F)
    1.00 to 1.22 kΩ
    40°C (104°F)
    0.80 to 1.00 kΩ
    45°C (113°F)
    0.65 to 0.85 kΩ
    50°C (122°F)
    0.50 to 0.70 kΩ
    55°C (131°F)
    0.44 to 0.60 kΩ
    60°C (140°F)
    0.36 to 0.50 kΩ

    NOTICE:
    1. Even slightly touching the thermistor may change the resistance value. Be sure to hold the connector of the thermistor.
    2. When measuring the resistance, the thermistor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (Refer to the graph).



NG
REPLACE THERMISTOR ASSEMBLY (A/C AMBIENT TEMPERATURE SENSOR) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (THERMISTOR - ACCESSORY METER)


    E170946E02
  1. Disconnect the A26 thermistor connector.

  1. Disconnect the A27 meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-3 (TH+) - A26-2
    Always
    Below 1 Ω
    A27-2 (SG) - A26-1
    A27-3 (TH+) - Body ground
    Always
    10 kΩ or higher
    A27-2 (SG) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ACCESSORY METER ASSEMBLY