Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Compressor Circuit

for Preparation Click here


DESCRIPTION

The air conditioning amplifier outputs the magnet clutch ON signal from terminal AC1 to the ECM. The ECM receives this signal and sends a signal from terminal ACT to the magnet clutch relay, turning the magnet clutch ON.

WIRING DIAGRAM


E171031E01


E171031E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (A/C Signal)
  1. Use the Data List to check if the A/C system is functioning properly.

    ECM 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    A/C signal / ON or OFF
    ON: A/C ON
    OFF: A/C OFF
    -

OK:
Display is as specified in normal condition.



NG
Go to step 7
OK


2.INSPECT MAGNET CLUTCH RELAY


    E170970E01
  1. Remove the magnet clutch relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET CLUTCH RELAY
OK


3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)


    E170963E10
  1. Disconnect the A37 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A37-13 (MGC) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (MGC VOLTAGE)


    E170941E15
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A37-13 (MGC) - Body ground
    Ignition switch START
    A/C switch ON
    Below 1 V
    Ignition switch START
    A/C switch OFF
    11 to 14 V



NG
Go to step 7
OK


5.INSPECT COOLER COMPRESSOR ASSEMBLY (MAGNET CLUTCH ASSEMBLY)


    E171839E02
  1. Disconnect the clutch connector.

  1. Apply battery voltage to the clutch and check operation of the clutch.

    OK:
    Measurement Connection
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Ground wire
    Magnet clutch engages



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (MAGNET CLUTCH ASSEMBLY)
OK


6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - MAGNET CLUTCH RELAY)


    E170965E03
  1. Disconnect the A1 compressor connector.

  1. Remove the magnet clutch relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A1-1 - M2-3
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)


    E171022E01
  1. Disconnect the A37 amplifier connector.

  1. Disconnect the E6*1, E13*2 or E10*3 ECM connector.

    1. *1: for 1KD-FTV or 2KD-FTV
    1. *2: for 1GR-FE
    1. *3: for 2TR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV or 2KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    A37-21 (AC1) - E6-18 (AC1)
    Always
    Below 1 Ω
    A37-7 (ACT) - E6-19 (ACT)
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A37-21 (AC1) - E13-24 (AC1)
    Always
    Below 1 Ω
    A37-7 (ACT) - E13-25 (ACT)
    for 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    A37-21 (AC1) - E10-24 (AC1)
    Always
    Below 1 Ω
    A37-7 (ACT) - E10-25 (ACT)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (AC1 VOLTAGE)


    E170941E16
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A37-21 (AC1) - Body ground
    Ignition switch START
    A/C switch AUTO
    Magnet clutch is engaged
    Below 1 V
    Ignition switch START
    A/C switch AUTO
    Magnet clutch is not engaged
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (ACT VOLTAGE)


    E170941E17
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A37-7 (ACT) - Body ground
    Ignition switch START
    A/C switch AUTO
    11 to 14 V



NG
REPLACE ECM
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)