Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

ECD SYSTEM (w/ EGR Cooler) > VC Output Circuit

for Preparation Click here


DESCRIPTION

The VC voltage (5 V) is generated in the ECM. The voltage is used to supply power to the throttle position sensor, EGR valve position sensor, manifold absolute pressure sensor and fuel pressure sensor.

WIRING DIAGRAM


A149982E03


A155930E02


INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.

    OK:
    MIL lights up



OK
SYSTEM OK
NG


2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and intelligent tester ON.

  1. Check the communication between the intelligent tester and ECM.

    Result:

    Condition
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT
A


3.CHECK ECM (VC VOLTAGE)
A154583E01
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Result:
    Tester Connection
    Specified Condition
    E8-18 (VC) - E8-28 (E2)
    Voltage is not 5 V


NEXT


4.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the T2 throttle position sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the throttle position sensor connector.



B
REPLACE THROTTLE BODY ASSEMBLY
A


5.CHECK MIL (EGR VALVE POSITION SENSOR)
  1. Disconnect the E2 EGR valve position sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Disconnect the EGR valve position sensor connector.



B
REPLACE EGR POSITION SENSOR
A


6.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the T9 manifold absolute pressure sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the manifold absolute pressure sensor connector.



B
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
A


7.CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the F9 fuel pressure sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the fuel pressure sensor connector.



B
REPLACE COMMON RAIL ASSEMBLY
A


8.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A13 accelerator pedal position sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the accelerator position sensor connector.



B
REPLACE ACCELERATOR PEDAL ASSEMBLY
A


9.CHECK WIRE HARNESS (VC - BODY GROUND)
A118271E05
  1. Disconnect the T2 throttle position sensor connector.

  1. Disconnect the E2 EGR valve position sensor connector.

  1. Disconnect the T9 manifold absolute pressure sensor connector.

  1. Disconnect the F9 fuel pressure sensor connector.

  1. Disconnect the A13 accelerator pedal position sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E8-18 (VC) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the EGR valve position sensor.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the accelerator pedal position sensor.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM