THEFT DETERRENT SYSTEM > TERMINALS OF ECU |
| CHECK THEFT WARNING ECU ASSEMBLY |

Disconnect the T16 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IG (T16-4) - E (T16-1) | R-L - W-B | Ignition power supply | Ignition switch OFF | Below 1 V |
| IG (T16-4) - E (T16-1) | R-L - W-B | Ignition power supply | Ignition switch ON | 10 to 14 V |
| +B1 (T16-3) - E (T16-1) | L-Y - W-B | +B (ECU-B) power source | Always | 10 to 14 V |
| +B2 (T16-12) - E (T16-1) | LG - W-B | +B (DOOR) power source | Always | 10 to 14 V |
| DSWH (T16-9) - E (T16-1) | G-R - W-B | Security courtesy switch input | Engine hood fully closed | 10 kΩ or higher |
| DSWH (T16-9) - E (T16-1) | G-R - W-B | Security courtesy switch input | Engine hood open | Below 1 Ω |
| E (T16-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| L2 (T16-20) - Body ground | L - Body ground | Door control switch (master switch) lock output | Door control switch (master switch) LOCK | Below 1 Ω |
| L2 (T16-20) - Body ground | L - Body ground | Door control switch (master switch) lock output | Door control switch (master switch) OFF | 10 kΩ or higher |
| UL3 (T16-21) - Body ground | L-W - Body ground | Door control switch (master switch) unlock output | Door control switch (master switch) UNLOCK | Below 1 Ω |
| UL3 (T16-21) - Body ground | L-W - Body ground | Door control switch (master switch) unlock output | Door control switch (master switch) OFF | 10 kΩ or higher |
| KSW (T16-5) - Body ground | G-Y - Body ground | Unlock warning switch | No key in ignition key cylinder | 10 kΩ or higher |
| KSW (T16-5) - Body ground | G-Y - Body ground | Unlock warning switch | Key inserted in ignition key cylinder | Below 1 Ω |
Reconnect the T16 ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IND (T16-22) - E (T16-1) | G-R - W-B | Security indicator light signal output | Security indicator light is flashing (theft deterrent system is operating) | Alternating between below 1 V and 10 to 14 V |
| CTY (T16-7) - E (T16-1) | R-L - W-B | All courtesy switch signals input | Driver side, front passenger side, rear RH or rear LH door closed | 10 to 14 V |
| CTY (T16-7) - E (T16-1) | R-L - W-B | All courtesy switch signals input | Driver side, front passenger side, rear RH or rear LH door open | Below 1 V |
| HORN (T16-24) - E (T16-1) | W-R - W-B | Both vehicle horn signals output (low pitched and high pitched) | Armed state | 10 to 14 V |
| HORN (T16-24) - E (T16-1) | W-R - W-B | Vehicle horn signal output | Alarm sounding state | Below 1 V |
| SH- (T16-26) - E (T16-1) | B - W-B | Security horn signal output | Security horn is sounding (theft deterrent system is in alarm sounding state) | Alternating between below 1 V and 10 to 14 V |
| HAZD (T16-23) - E (T16-1) | G-O - W-B | All hazard warning light signals output | Hazard warning lights are flashing (theft deterrent system is in alarm sounding state) | Alternating between below 1 V and 10 to 14 V |
| SPD (T16-15) - E (T16-1) | V-R - W-B | Speed signal from combination meter | Ignition switch ON, one driving wheel is rotating slowly | Pulse generation (see waveform) |
![]() |
Waveform
Vehicle speed signal
| Item | Content |
| Symbols (Terminal No.) | SPD (T16-15) - E (T16-1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | While driving vehicle |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (INTEGRATION RELAY) |

Disconnect the 2A, 2D and 2L junction block connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| BECU (2L-12) - GND (2D-9) | L - W-B | +B (BECU) power source | Always | 10 to 14 V |
| GND (2D-9, 18) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| L1 (2A-4) - Body ground | L - Body ground | Door control switch (master switch) lock input | Door control switch (master switch) LOCK | 10 kΩ or higher |
| L1 (2A-4) - Body ground | L - Body ground | Door control switch (master switch) lock input | Door control switch (master switch) OFF | Below 1 Ω |
| UL1 (2D-4) - Body ground | L-W - Body ground | Door control switch (master switch) unlock input | Door control switch (master switch) UNLOCK | 10 kΩ or higher |
| UL1 (2D-4) - Body ground | L-W - Body ground | Door control switch (master switch) unlock input | Door control switch (master switch) OFF | Below 1 Ω |
Reconnect the 2A, 2D and 2L junction block connectors.
Measure the voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| ACT+ (2R-28) - Body ground | L - Body ground | Door lock motor LOCK drive output (driver side door) | Door control switch (master switch) or driver side door key cylinder OFF | Below 1 V |
| ACT+ (2R-28) - Body ground | L - Body ground | Door lock motor LOCK drive output (driver side door) | Door control switch (master switch) or driver side door key cylinder LOCK | 10 to 14 V |
| ACT- (2R-27) - Body ground | L-Y - Body ground | Door lock motor UNLOCK drive output (driver side door) | Door control switch (master switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (2R-27) - Body ground | L-Y - Body ground | Door lock motor UNLOCK drive output (driver side door) | Door control switch (master switch) or driver side door key cylinder UNLOCK | 10 to 14 V |
| DCTY (2O-27) - Body ground | R-B - Body ground | Driver side courtesy switch input | Driver side door closed | 10 to 14 V |
| DCTY (2O-27) - Body ground | R-B - Body ground | Driver side courtesy switch input | Driver side door open | Below 1 V |