DIFFERENTIAL LOCK SYSTEM > INSPECTION |
| 1. INSPECT DIFFERENTIAL LOCK SYSTEM |
![]() |
Inspect the indicator light.
Check that the indicator light lights up for appox. 1 second when the ignition switch is turned ON.
Inspect the differential lock operation.
Jack up the vehicle then start the engine.
Shift the transfer shift lever to L position.
When the differential lock control switch is set to the ON position, the indicator light is pushed on. Differential lock is applied to the rear wheel at this time.
When the differential lock control switch is at the OFF position, the indicator light goes off. Differential lock is released for the rear wheel at this time.
![]() |
Check the voltage between the terminals of the four wheel drive control ECU when switching the differential control switch with the speedmemter, registering approx. 8 km/h (5 mph) or more.
| Switch position | Terminal | Specified value |
| ON | M1 to M2 | 0.5 V or less (No change) |
Return the differential lock control switch to OFF.
Stop the engine and lower the vehicle.
| 2. CHECK WIRE HARNESS AND CONNECTOR |
![]() |
Inspect the system circuit with the connector disconnected.
Disconnect the connector from the four wheel drive control ECU and inspect the connector on the wire harness side, as shown in the table.
| Tester Connection | Trouble Part | Condition | Specified value |
| M1 - M2 | Rear differential lock actuator | - | Less than 100 Ω |
| GND - Body ground | Body ground | - | Continuity |
| SPD - Body ground | Speed sensor | Vehicle moves slowly | 1 pulse 40 cm (15.75 in.) |
| IG - Body ground | Differential fuse | Ignition switch ON | 10 to 14 V |
| RLP - Body ground | Rear differential lock indicator switch | Ignition switch ON with indicator light ON | About 0 V |
| Ignition switch ON with indicator light OFF | 10 to 14 V | ||
| 4WD - Body ground | L position switch | Ignition switch ON with transfer shift lever except L | About 0 V |
| Ignition switch ON with transfer shift lever L | 10 to 14 V | ||
| R - Body ground | Differential lock control switch | Ignition switch ON with differential lock control switch ON | 10 to 14 V |
| Ignition switch ON with differential lock control switch OFF | About 0 V |
| 3. CHECK FOUR WHEEL DRIVE CONTROL ECU |
![]() |
Inspect the system circuit with the connector connected.
Turn the ignition switch to the ON position.
Shift the transfer shift lever to L position.
Using a voltmeter, measure the voltage when the differential lock control switch is in the position, as shown in the table.
| Tester connection | Switch position | Specified value |
| 4WD - GND | - | 0.5 V or less |
| RLP - GND | ON*
| 0.5 V or less |
| M1 - M2 | OFF → ON | 0.5 V or less → 10 to 14 V (approx. 1 sec.) → 0.5 V or less |
| M2 - M1 | ON → OFF |
Install the ECU in place.
| 4. INSPECT DIFFERENTIAL LOCK COMPONENTS |
Inspect the relay operation.
Jack up the vehicle.
Use a heater main relay and connect it, as shown below.
Rotate the tire and check that the differential lock has occurred.

| 5. INSPECT DIFFERENTIAL LOCK SWITCH |
![]() |
Inspect the differential lock switch.
Inspect the resistance between terminals 1and 4.
| 6. INSPECT NO. 4 TRANSFER INDICATOR SWITCH |
![]() |
Inspect the No. 4 transfer indicator switch.
Measure the resistance between the terminals when the switch is pushed (differential connected position).
Measure the resistance between the terminals when switch is free (differential disconnected position).
Inspect the L position switch .
Inspect the vehicle speed sensor (Click here).