Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/o EGR Cooler)

DTC    U0101    Lost Communication with TCM

for Preparation Click here


DESCRIPTION

The ECM (engine control unit) intercommunicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).
If there is a problem in this intercommunication, the ECM sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
U0101
  1. Following conditions are met for 1.25 seconds (1 trip detection logic):
    1. Ignition switch ON
    2. Battery voltage is 10.5 V or more
    3. No intercommunication between ECM and TCM
  1. ECM
  2. TCM
  3. ECM to TCM circuit

WIRING DIAGRAM


A159341E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    U0101
    A
    U0101 and other DTCs
    B

    HINT:
    If any DTCs other than U0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT TCM


    G037243E06
  1. Disconnect the T17 TCM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    BATT (T17-5) - Body ground
    11 to 14 V



    F045523E33
  1. Disconnect the T19 TCM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E1 (T19-1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (ECM - TCM)


    G034917E07
  1. Disconnect the E6 ECM connector.

  1. Disconnect the T17 TCM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    CAN+ (E6-22) - CAN+ (T17-21)
    Below 1 Ω
    CAN- (E6-21) - CAN- (T17-20)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    CAN+ (E6-22) or CAN+ (T17-21) - Body ground
    10 kΩ or higher
    CAN- (E6-21) or CAN- (T17-20) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    No output
    A
    U0101
    B



B
REPLACE TCM
A

END