Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P1264    VN Turbo Controller Malfunction

for Preparation Click here


DESCRIPTION

The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, the turbo motor driver and ECM.
The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure. When the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.
The turbocharger actuator built on the turbocharger activates the nozzle vane. The nozzle vane position sensor built on the actuator detects the opening angle of nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position sensor signal. Based on these signals, the turbo motor driver operates the DC motor and controls the turbocharger's opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM
The ECM sends an opening angle request signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.

A158389E02


DTC No.
DTC Detection Condition
Trouble Area
P1264
When communication error occurs between turbo motor and ECM
(1 trip detection logic)
  1. Turbo motor driver
  2. Open or short in turbo motor driver circuit
  3. Turbo motor driver ground problem
  4. ECM

WIRING DIAGRAM


A150283E09


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT TURBO MOTOR DRIVER


    A150167E07
  1. Disconnect the T8 turbo motor driver connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the turbo motor driver connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (T8-3) - GND (T8-4)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)


    A149857E08
  1. Disconnect the E8 ECM connector.

  1. Disconnect the T8 turbo motor driver connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VNTO (E8-10) - VNTO (T8-7)
    Below 1 Ω
    VNTI (E8-17) - VNTI (T8-2)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VNTO (E8-10) or VNTO (T8-7) - Body ground
    10 kΩ or higher
    VNTI (E8-17) or VNTI (T8-2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VNTO VOLTAGE)


    A099245E10
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    Standard voltage:
    Tester Connection
    Specified Condition
    VNTO (E8-10) - E1 (E7-7)
    Correct waveform is as shown



NG
REPLACE ECM (Click here)
OK


4.INSPECT TURBO MOTOR DRIVER (VNTI VOLTAGE)


    G036520E10
  1. While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

    Standard voltage:
    Tester Connection
    Specified Condition
    VNTI (E8-17) - E1 (E7-7)
    Correct waveform is as shown



NG
REPLACE TURBO MOTOR DRIVER
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)