Home › SECURITIES › ENGINE IMMOBILISER › TRANSPONDER KEY AMPLIFIER

TRANSPONDER KEY AMPLIFIER > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
For vehicles with SRS:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE LOWER NO. 2 STEERING WHEEL COVER (w/ Airbag System, w/ Steering Pad Switch)


    B176820
  1. Using a screwdriver, detach the 2 claws and remove the No. 2 steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE LOWER NO. 3 STEERING WHEEL COVER (w/ Airbag System, w/ Steering Pad Switch)


    B176819
  1. Using a screwdriver, detach the 2 claws and remove the No. 3 steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


5. REMOVE STEERING PAD ASSEMBLY (w/ Airbag System, w/ Steering Pad Switch)


B112129E01
  1. Straighten the front wheels.

  1. Using a T30 "torx" socket, loosen the 2 screws until the groove along each screw circumference catches on the screw case.



    B085362E03
  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the airbag connector.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



6. REMOVE STEERING PAD ASSEMBLY (w/ Airbag System, w/o Steering Pad Switch)


B112129E01
  1. Straighten the front wheels.

  1. Using a T30 "torx" socket, loosen the 2 screws until the groove along each screw circumference catches on the screw case.



    B085362E03
  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the airbag connector.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



7. REMOVE STEERING PAD ASSEMBLY (w/o Airbag System, w/o Steering Pad Switch)


  1. for Type A:



      B207733
    1. Detach the 4 claws and pull off the steering pad from the steering wheel as shown in the illustration.



  1. for Type B:



      C194096
    1. Remove the screw.



    2. C194097
    3. Detach the 3 clips and pull off the steering pad from the steering wheel as shown in the illustration.

    4. Disconnect the horn connector.



8. REMOVE STEERING WHEEL ASSEMBLY (w/ Airbag System, w/ Steering Pad Switch)


    B206142
  1. Disconnect steering pad switch connector.

  1. Remove the steering wheel set nut.



    G039068E01
  1. Place matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



9. REMOVE STEERING WHEEL ASSEMBLY (w/ Airbag System, w/o Steering Pad Switch)


G039068E01
  1. Remove the steering wheel set nut.

  1. Place matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



10. REMOVE STEERING WHEEL ASSEMBLY (w/o Airbag System, w/o Steering Pad Switch)


G039068E01
  1. Remove the steering wheel set nut.

  1. Place matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



11. REMOVE LOWER STEERING COLUMN COVER


G039357E01
  1. Remove the 3 screws and cover lower.



12. REMOVE UPPER STEERING COLUMN COVER


G039357E01
  1. Remove the 3 screws and cover lower.



13. REMOVE TRANSPONDER KEY AMPLIFIER
  1. Disconnect the amplifier connector.



    G034347E02
  1. Using a screwdriver, widen the claw attached to the upper bracket by approximately 1.0 mm (0.039 in.).

  1. Pull out the transponder key amplifier with the claw open.