FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY |
| 1. REMOVE RECLINING POWER SEAT SWITCH KNOB |
![]() |
Apply protective tape around the cushion shield.
Using a screwdriver, detach the 2 claws and remove the knob.
| 2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver, detach the 4 claws and remove the knob.
| 3. REMOVE FRONT SEAT CUSHION SHIELD RH |
![]() |
Remove the 2 screws.
![]() |
Remove the 3 screws.
Detach the claw and guide.
Remove the cushion shield.
| 4. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD |
![]() |
Remove the 2 screws.
Detach the 2 claws and remove the cushion shield.
| 5. REMOVE FRONT POWER SEAT SWITCH |
![]() |
Remove the 3 screws.
Disconnect the connector and remove the switch.
| 6. REMOVE FRONT SEAT CUSHION INNER SHIELD RH |
![]() |
Remove the screw.
Pull the cushion inner shield to detach the claw and guide.
![]() |
Pull the cushion inner shield to detach the claw and remove the cushion inner shield.
| 7. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH |
![]() |
Detach the clamp.
![]() |
Detach the wire harness from the clamp.
Remove the nut and seat belt.
Remove the buckle cover.
| 8. REMOVE FRONT SEAT CUSHION COVER RH |
Remove the cover.
| 9. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Remove the hog rings.
Detach the hooks and remove the seat cushion cover with pad.

| 10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the hog rings and seat cushion cover.
| 11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the hog rings from the wires of the seatback cover. Then roll up the seatback cover.
![]() |
Remove the hog rings and roll up the seatback cloth.
![]() |
Remove the hog rings and detach the strap of the seatback cover. Then roll up the seatback cover.
![]() |
Remove the hog rings from the center of the seatback pad and roll up the seatback cover.
![]() |
Remove the hog rings from the upper part of the seatback pad. Then roll up the seatback cover.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
![]() |
Remove the hog rings and seatback cover.
| 12. REMOVE SEPARATE TYPE FRONT SEATBACK PAD |
![]() |
Remove the seatback pad.
| 13. REMOVE NO. 1 SEATBACK CLOTH |
![]() |
Remove the seatback cloth.
| 14. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the screw.
Detach the claw and remove the cover.
| 15. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the screw.
Detach the guide and remove the cover.
| 16. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Detach the claw and remove the cover.
| 17. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Detach the guide and remove the cover.
| 18. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) |
![]() |
Detach the 8 hooks and remove the seatback spring.
Disconnect the connector.
![]() |
Detach the 6 claws and remove the push nut from the reclining rod.
![]() |
Remove the reclining rod.
![]() |
Using a 4 mm socket hexagon wrench, remove the 3 bolts and motor.
| 19. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Slide) |
![]() |
Detach the 2 wire harness clamps.
Detach the 4 clamps indicated by the arrows in the illustration and remove the seat cushion spring.
![]() |
Remove the 4 bolts and seat cushion frame.
![]() |
Put matchmarks on the seat track rail and sliding unit of the seat frame.
Disconnect the connector.
![]() |
Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat to the foremost position.
![]() |
Detach the claw and disconnect the connector from the seat frame.
Loosen the 2 nuts.
![]() |
Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1 and slide the seat to the rearmost position.
![]() |
Using a 5 mm socket hexagon wrench, remove the 2 bolts.
Using a 4 mm socket hexagon wrench, remove the 4 bolts.
Remove the 2 nuts and front power seat motor assembly with slide cable.
![]() |
Remove the slide cable.
| 20. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Rear Lifter) |
![]() |
Detach the 2 wire harness clamps.
Detach the 4 clamps indicated by the arrows in the illustration and remove the seat cushion spring.
![]() |
Remove the 4 bolts and seat cushion frame.
![]() |
Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts for the tilt rod.
Remove the nut and tilt rod.
![]() |
Disconnect the connector.
Using a T40 "TORX" socket wrench, remove the "TORX" bolt for the adjust screw.
Using a 4 mm socket hexagon wrench, remove the 2 bolts and motor.
| 21. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH |
![]() |
Remove the screw.
Detach the 4 claws and remove the lower seat cushion shield.
| 22. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH |
![]() |
Remove the screw.
Detach the 4 claws and remove the lower seat cushion shield.
| 23. REMOVE FRONT SEAT WIRE RH |
![]() |
Disconnect the connector.
Detach the wire harness clamp.
Detach the 2 claws and remove the seat wire.
| 24. REMOVE FRONT NO. 2 SEAT WIRE RH |
![]() |
Detach the 2 wire harness clamps and remove the seat wire.
| 25. REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY |
![]() |
Remove the 4 bolts and seatback spring.