Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

E171001E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AIR (A37-22) - GND (A37-1)
    L-W - L
    Air inlet damper servo motor operation voltage
    Ignition switch ON
    Fresh switch ON
    Below 1 V
    AIR (A37-22) - GND (A37-1)
    L-W - L
    Air inlet damper servo motor operation voltage
    Ignition switch ON
    Recirculation switch ON
    11 to 14 V
    AIF (A37-23) - GND (A37-1)
    G-Y - L
    Air inlet damper servo motor operation voltage
    Ignition switch ON
    Recirculation switch ON
    Below 1 V
    AIF (A37-23) - GND (A37-1)
    G-Y - L
    Air inlet damper servo motor operation voltage
    Ignition switch ON
    Fresh switch ON
    11 to 14 V
    AOF (A37-3) - GND (A37-1)
    Y-B - L
    Air vent mode damper servo motor operation voltage
    Ignition switch ON
    Mode switch DEF
    Below 1 V
    AOF (A37-3) - GND (A37-1)
    Y-B - L
    Air vent mode damper servo motor operation voltage
    Ignition switch ON
    Mode switch FACE
    11 to 14 V
    AOD (A37-4) - GND (A37-1)
    R-B - L
    Air vent mode damper servo motor operation voltage
    Ignition switch ON
    Mode switch FACE
    Below 1 V
    AOD (A37-4) - GND (A37-1)
    R-B - L
    Air vent mode damper servo motor operation voltage
    Ignition switch ON
    Mode switch DEF
    11 to 14 V
    PIA (A38-17) - SG-7 (A38-21)
    P-B - LG-R
    Input signal for pulse position sensor (Air inlet damper servo motor)
    Ignition switch ON
    Air inlet control:
    Changed from RECIRCULATION to FRESH or vice versa
    Pulse generation
    PIB (A38-16) - SG-7 (A38-21)
    R-L - LG-R
    Input signal for pulse position sensor (Air inlet damper servo motor)
    Ignition switch ON
    Air inlet control:
    Changed from RECIRCULATION to FRESH or vice versa
    Pulse generation
    SG-7 (A38-21) - Body ground
    LG-R - Body ground
    Ground for pulse position sensor (Air inlet damper servo motor)
    Always
    Below 1 Ω
    POA (A38-26) - SG-2 (A38-11)
    L-O - L-Y
    Input signal for pulse position sensor (Air vent mode damper servo motor)
    Ignition switch ON
    Mode control:
    Changed from FACE to DEF or vice versa
    Pulse generation
    POB (A38-25) - SG-2 (A38-11)
    LG - L-Y
    Input signal for pulse position sensor (Air vent mode damper servo motor)
    Ignition switch ON
    Mode control:
    Changed from FACE to DEF or vice versa
    Pulse generation
    SG-2 (A38-11) - Body ground
    L-Y - Body ground
    Ground for pulse position sensor (Air vent mode damper servo motor)
    Always
    Below 1 Ω
    TE (A38-1) - SG-4 (A38-14)
    G - P
    A/C evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature:
    0°C (32°F)
    2 to 2.4 V
    TE (A38-1) - SG-4 (A38-14)
    G - P
    A/C evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature:
    15°C (59°F)
    1.4 to 1.8 V
    SG-4 (A38-14) - Body ground
    P - Body ground
    Ground for A/C evaporator temperature sensor
    Always
    Below 1 Ω
    IG+ (A37-6) - GND (A37-1)
    R-L - L
    Power source (IG)
    Ignition switch off or ACC
    Below 1 V
    IG+ (A37-6) - GND (A37-1)
    R-L - L
    Power source (IG)
    Ignition switch ON
    11 to 14 V
    +B1 (A37-5) - GND (A37-1)
    L-Y - L
    Power source (Back-up)
    Always
    11 to 14 V
    GND (A37-1) - Body ground
    L - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    BLW (A37-2) - GND (A37-1)
    L-B - L
    Blower motor speed control voltage
    Ignition switch ON
    Blower switch ON (LO)
    Pulse generation
    (see waveform 1)
    TS (A38-7) - S5-3 (A38-2)
    L-W - W-R
    A/C solar sensor signal
    Ignition switch ON
    0.8 to 4.3 V
    S5-3 (A38-2) - GND (A37-1)
    W-R - L
    Power supply for solar sensor
    Ignition switch ON
    4.5 to 5.5 V
    HR (A37-14) - GND (A37-1)
    L-W - L
    HTR relay signal
    Ignition switch ON
    Blower switch OFF
    11 to 14 V
    HR (A37-14) - GND (A37-1)
    L-W - L
    HTR relay signal
    Ignition switch ON
    Blower switch ON
    Below 1 V
    TR (A38-18) - SG-3 (A38-13)
    GR - BR-Y
    A/C room temperature sensor signal
    Ignition switch ON
    Cabin temperature:
    25°C (77°F)
    1.8 to 2.2 V
    TR (A38-18) - SG-3 (A38-13)
    GR - BR-Y
    A/C room temperature sensor signal
    Ignition switch ON
    Cabin temperature:
    40°C (104°F)
    1.2 to 1.6 V
    SG-3 (A38-13) - Body ground
    BR-Y - Body ground
    Ground for A/C room temperature sensor
    Always
    Below 1 Ω
    RDFG (A37-12) - GND (A37-1)
    R-L - L
    Rear defogger switch signal
    Ignition switch ON
    Rear defogger switch OFF
    11 to 14 V
    RDFG (A37-12) - GND (A37-1)
    R-L - L
    Rear defogger switch signal
    Ignition switch ON
    Rear defogger switch ON
    Below 1 V
    ACT (A37-7) - GND (A37-1)
    R-L - L
    Magnet clutch on permit input signal
    Ignition switch START
    Magnet clutch ON: Not permitted
    Below 1 V
    ACT (A37-7) - GND (A37-1)
    R-L - L
    Magnet clutch on permit input signal
    Ignition switch START
    Magnet clutch ON: Permitted
    11 to 14 V
    AC1 (A37-21) - GND (A37-1)
    Y - L
    Idle-up request signal
    Ignition switch START
    Magnet clutch: Not engaged
    11 to 14 V
    AC1 (A37-21) - GND (A37-1)
    Y - L
    Idle-up request signal
    Ignition switch START
    Magnet clutch: Engaged
    Below 1 V
    SPD (A37-9) - GND (A37-1)
    V-W - L
    Vehicle speed signal
    Driving at approx. 20 km/h (12 mph)
    Pulse generation
    (see waveform 2)
    PSW (A38-5) - GND (A37-1)
    Y-B - L
    Pressure switch signal
    Ignition switch START
    Refrigerant pressure: Normal
    Below 1 V
    PSW (A38-5) - GND (A37-1)
    Y-B - L
    Pressure switch signal
    Ignition switch START
    Refrigerant pressure:
    Less than 0.196 MPa (2.0 kgf/cm2, 28 psi) or more than 3.14 MPa (32.0 kgf/cm2, 455 psi)
    11 to 14 V
    TAMO (A37-18) - GND (A37-1)
    P - L
    A/C ambient temperature signal
    Ignition switch ON
    Pulse generation
    MGC (A37-13) - GND (A37-1)
    B - L
    Magnet clutch signal
    Ignition switch START
    Magnet clutch: Not engaged
    11 to 14 V
    MGC (A37-13) - GND (A37-1)
    B - L
    Magnet clutch signal
    Ignition switch START
    Magnet clutch: Engaged
    Below 1 V
    SW 1 (A37-16) - GND (A37-1)
    G-O - L
    Hazard warning switch signal
    Hazard warning switch signal OFF
    11 to 14 V
    SW 1 (A37-16) - GND (A37-1)
    G-O - L
    Hazard warning switch signal
    Hazard warning switch signal ON
    Below 1 V
    ILL+ (A37-15) - GND (A37-1)
    G - L
    Power supply for illumination
    Light control switch OFF
    Below 1 V
    ILL+ (A37-15) - GND (A37-1)
    G - L
    Power supply for illumination
    Light control switch TAIL
    11 to 14 V
    AMC (A37-19) - GND (A37-1)
    R-W - L
    Air mix damper servo motor operation signal
    Ignition switch ON
    Temperature switch Max. HOT
    Below 1 V
    AMC (A37-19) - GND (A37-1)
    R-W - L
    Air mix damper servo motor operation signal
    Ignition switch ON
    Temperature switch Max. COOL
    11 to 14 V
    AMH (A37-17) - GND (A37-1)
    L - L
    Air mix damper servo motor operation signal
    Ignition switch ON
    Temperature switch Max. HOT
    11 to 14 V
    AMH (A37-17) - GND (A37-1)
    L - L
    Air mix damper servo motor operation signal
    Ignition switch ON
    Temperature switch Max. COOL
    Below 1 V
    PMA (A38-24) - SG-1 (A38-20)
    W-R - BR-Y
    Input signal for pulse position sensor (Air mix damper servo motor)
    Ignition switch ON
    Temperature switch: Max. COOL → Max. HOT
    Pulse generation
    PMB (A38-23) - SG-1 (A38-20)
    W-L - BR-Y
    Input signal for pulse position sensor (Air mix damper servo motor)
    Ignition switch ON
    Temperature switch: Max. HOT → Max. COOL
    Pulse generation
    SG-1 (A38-20) - Body ground
    BR-Y - Body ground
    Ground for pulse position sensor (Air mix damper servo motor)
    Always
    Below 1 V
    TW (A37-8) - GND (A37-1)
    P - L
    Engine coolant temperature sensor signal
    Ignition switch ON
    Pulse generation

    w/ PTC heater 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PTCR (A36-3) - GND (A37-1)
    L-W - L
    Idle-up request signal
    Ignition switch ON
    Power heater switch OFF
    11 to 14 V
    PTCR (A36-3) - GND (A37-1)
    L-W - L
    Idle-up request signal
    Ignition switch ON
    Power heater switch ON
    Below 1 V
    IGN (A37-11) - GND (A37-1)
    B-W - L
    Engine speed signal
    Ignition switch ON
    Pulse generation
    TAIL (A36-7) - GND (A37-1)
    G - L
    Light control switch signal
    Light control switch OFF
    Below 1 V
    ALT (A36-6) - GND (A37-1)
    G - L
    Generator input signal
    Engine idling
    Pulse generation
    PTC1 (A36-1) - GND (A37-1)
    R-W - L
    No. 1 PTC heater relay signal
    Ignition switch ON
    Generator is operating
    Temperature switch Max. HOT
    Coolant temperature:
    Below 65°C (149°F)
    Ambient temperature:
    Below 10°C (50°F)
    Power heater switch ON
    Blower switch ON (LO)
    11 to 14 V
    PTC2 (A36-2) - GND (A37-1)
    GR - L
    No. 2 PTC heater relay signal
    Ignition switch ON
    Generator is operating
    Temperature switch Max. HOT
    Coolant temperature:
    Below 65°C (149°F)
    Ambient temperature:
    Below 10°C (50°F)
    Power heater switch ON
    Blower switch ON (LO)
    11 to 14 V
    HEAT (A36-8) - GND (A37-1)
    L-O - L
    Power heater switch input signal
    Ignition switch ON
    Power heater switch ON
    Below 1 V
    HEAT (A36-8) - GND (A37-1)
    L-O - L
    Power heater switch input signal
    Ignition switch ON
    Power heater switch OFF
    11 to 14 V
    SWIN (A36-5) - GND (A37-1)
    P - L
    Power heater switch indicator light signal
    Ignition switch ON
    Power heater switch ON
    Below 1 V
    SWIN (A36-5) - GND (A37-1)
    P - L
    Power heater switch indicator light signal
    Ignition switch ON
    Power heater switch OFF
    11 to 14 V

    1. If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.



  2. E171008E02
  3. Using an oscilloscope, check waveform 1.
    Blower motor control signal 
    Item
    Content
    Symbols (Terminal No.)
    BLW (A37-2) - GND (A37-1)
    Tool Setting
    1 V/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, Blower switch ON (LO)

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.



  4. E171009E01
  5. Using an oscilloscope, check waveform 2.
    Vehicle speed signal 
    Item
    Content
    Symbols (Terminal No.)
    SPD (A37-9) - GND (A37-1)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Driving at approx. 20 km/h (12 mph)

    HINT:
    As the vehicle speed increases, the wavelength becomes shorter.


CHECK ECM (for 1KD-FTV, 2KD-FTV)

E170985E01

  1. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ACT (E6-19) - E1 (E7-7)
    R-L - BR
    Magnet clutch on permit output signal
    Ignition switch START
    Magnet clutch ON:
    Not permitted
    Below 1 V
    ACT (E6-19) - E1 (E7-7)
    R-L - BR
    Magnet clutch on permit output signal
    Ignition switch START
    Magnet clutch ON:
    Permitted
    11 to 14 V
    AC1 (E6-18) - E1 (E7-7)
    Y - BR
    Idle-up request signal
    Ignition switch START
    Magnet clutch:
    Engaged
    Below 1 V
    AC1 (E6-18) - E1 (E7-7)
    Y - BR
    Idle-up request signal
    Ignition switch START
    Magnet clutch:
    Not engaged
    11 to 14 V
    THWO (E5-2) - E1 (E7-7)
    P - BR
    Ignition switch ON
    Ignition switch START
    Pulse generation
    TACH (E5-4) - E1 (E7-7)
    B-W - BR
    Tachometer signal
    Engine running
    Pulse generation
    THW (E8-19) - E2 (E8-28)
    R-L - BR
    Engine coolant temperature sensor signal
    Ignition switch START
    Engine coolant temperature 20°C (68°F)
    0.2 to 1.0 V

    w/ PTC heater 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    HSW (E6-16) - E1 (E7-7)
    L-W - BR
    Heater switch output signal for idle-up
    Ignition switch START
    Blower switch ON
    Power heater switch ON
    Temperature switch Max. HOT
    Below 1 V
    HSW (E6-16) - E1 (E7-7)
    L-W - BR
    Heater switch output signal for idle-up
    Ignition switch START
    Blower switch OFF
    Power heater switch ON
    Temperature switch Max. HOT
    11 to 14 V
    If the result is not as specified, the ECM may have a malfunction.


CHECK ECM (for 1GR-FE)

E127538E01

  1. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ACT (E13-25) - E1 (E17-1)
    R-L - BR
    Magnet clutch on permit output signal
    Ignition switch ON
    Magnet clutch ON:
    Not permitted
    Below 1 V
    ACT (E13-25) - E1 (E17-1)
    R-L - BR
    Magnet clutch on permit output signal
    Ignition switch ON
    Magnet clutch ON:
    Permitted
    11 to 14 V
    AC1 (E13-24) - E1 (E17-1)
    Y - BR
    Idle-up request signal
    Ignition switch ON
    Magnet clutch:
    Engaged
    Below 1 V
    AC1 (E13-24) - E1 (E17-1)
    Y - BR
    Idle-up request signal
    Ignition switch ON
    Magnet clutch:
    Not engaged
    11 to 14 V
    THW (E15-21) - E2 (E15-28)
    B - BR
    Engine coolant temperature sensor signal
    Ignition switch START
    Engine coolant temperature 20°C (68°F)
    0.2 to 1.0 V
    THWO (E13-14) - E1 (E17-1)
    P - BR
    Ignition switch ON
    Ignition switch START
    Pulse generation
    TACH (E13-1) - E1 (E17-1)
    B-W - BR
    Tachometer signal
    Engine running
    Pulse generation
    If the result is not as specified, the ECM may have a malfunction.


CHECK ECM (for 2TR-FE)

E170985E03

  1. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ACT (E10-25) - E1 (E12-3)
    R-L - BR
    Magnet clutch on permit output signal
    Ignition switch START
    Magnet clutch ON:
    Not permitted
    Below 1 V
    ACT (E10-25) - E1 (E12-3)
    R-L - BR
    Magnet clutch on permit output signal
    Ignition switch START
    Magnet clutch ON:
    Permitted
    11 to 14 V
    AC1 (E10-24) - E1 (E12-3)
    Y - BR
    Idle-up request signal
    Ignition switch START
    Magnet clutch:
    Engaged
    Below 1 V
    AC1 (E10-24) - E1 (E12-3)
    Y - BR
    Idle-up request signal
    Ignition switch START
    Magnet clutch:
    Not engaged
    11 to 14 V
    THWO (E10-14) - E1 (E12-3)
    P - BR
    Ignition switch ON
    Ignition switch START
    Pulse generation
    TACH (E10-1) - E1 (E12-3)
    B-W - BR
    Tachometer signal
    Engine running
    Pulse generation
    THW (E12-32) - E2 (E12-28)
    B - BR
    Engine coolant temperature sensor signal
    Ignition switch START
    Engine coolant temperature 20°C (68°F)
    0.2 to 1.0 V
    If the result is not as specified, the ECM may have a malfunction.


CHECK ACCESSORY METER ASSEMBLY

E165586E03

  1. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    TH+ (A27-3) - SG (A27-2)
    W-G - BR-Y
    A/C ambient temperature sensor signal
    Ignition switch ON
    Ambient temperature:
    20 to 30°C (68 to 86°F)
    1 to 1.6 V
    TH+ (A27-3) - SG (A27-2)
    W-G - BR-Y
    A/C ambient temperature sensor signal
    Ignition switch ON
    Ambient temperature:
    30 to 50°C (86 to 122°F)
    0.6 to 1 V
    DATA (A27-9) - GND1 (A27-1)
    P - LG
    A/C ambient temperature sensor signal
    Ignition switch ON
    Pulse generation

    1. If the result is not as specified, the accessory meter assembly may have a malfunction.


CHECK COMBINATION METER ASSEMBLY

E165587E02

  1. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    C8-6 - C8-22
    V-R - Y
    Vehicle speed signal
    Driving at approx. 20 km/h (12 mph)
    Pulse generation

    1. If the result is not as specified, the combination meter assembly may have a malfunction.