REAR DIFFERENTIAL CARRIER ASSEMBLY (for DANA Made) > REASSEMBLY > Preparation
|  |
|
SST

| 09308-00010
| Oil Seal Puller
| 
| 09316-60011
| Transmission & Transfer Bearing Replacer
| 
| (09316-00011)
| Replacer Pipe
| 
| (09316-00021)
| Replacer A
| 
| (09316-00041)
| Replacer C
| 
| 09330-00021
| Companion Flange Holding Tool
| 
| (09330-00030)
| Pin
| 
| 09504-00011
| Differential Side Bearing Adjusting Nut Wrench
| 
| 09506-30012
| Differential Drive Pinion Rear Bearing Cone Replacer
| 
| 09636-20010
| Upper Ball Joint Dust Cover Replacer
| 
| 09930-00010
| Drive Shaft Nut Chisel
| 
| (09931-00010)
| Handle
| 
| (09931-00020)
| Nut Chisel
| 
| 09950-30012
| Puller A Set
| 
| (09951-03010)
| Upper Plate
| 
| (09953-03010)
| Center Bolt
| 
| (09954-03010)
| Arm
| 
| (09955-03030)
| Lower Plate 130
| 
| (09956-03040)
| Adapter 22
| 
| 09950-60010
| Replacer Set
| 
| (09951-00430)
| Replacer 43
| 
| (09951-00470)
| Replacer 47
| 
| (09951-00480)
| Replacer 48
| 
| (09951-00550)
| Replacer 55
| 
| 09950-70010
| Handle Set
| 
| (09951-00560)
| Replacer 56
| 
| (09951-00570)
| Replacer 57
| 
| (09951-07150)
| Handle 150
| 
| 09960-10010
| Variable Pin Wrench Set
| 
| (09962-01000)
| Variable Pin Wrench Arm Assembly
| 
| (09963-00700)
| Pin 7
| |
|
EQUIPMENTBrass bar
| -
| Chisel
| -
| Dial indicator
| -
| Feeler gauge
| -
| Hammer
| -
| Micrometer
| -
| Needle nose pliers
| -
| Plastic hammer
| -
| Press
| -
| Red lead
| -
| Screwdriver
| -
| Tape
| -
| Torque wrench
| -
| Vernier calipers
| -
| |
|
LUBRICANT / Front differentialItem
| Capacity
| Oil grade
| Classification
| w/ A.D.D.
| 1.60 to 1.70 liters (1.69 to 1.80 US qts, 1.40 to 1.50 Imp. qts.)
| Hypoid gear oil API GL-5 or equivalent
| Above-18°C (0°F): SAE 90 Below-18°C (0°F): SAE 75W-90
| w/o A.D.D.
| 1.40 to 1.50 liters (1.48 to 1.59 US qts, 1.23 to 1.31 Imp. qts.)
| Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 85W-90
|
LUBRICANT / Rear differential (TMT made)Item
| Capacity
| Oil grade
| Classification
| 2WD
| 3.15 to 3.25 liters (3.30 to 3.43 US qts, 2.77 to 2.86 Imp. qts.)
| Hypoid gear oil API GL-5 or equivalent
| Above-18°C (0°F): SAE 90 Below-18°C (0°F): SAE 85W-90
| 2WD (for LSD)
| Hypoid gear oil LSD API GL-5 or equivalent
| 4WD
| 3.30 to 3.40 liters (3.49 to 3.59 US qts, 2.90 to 2.99 Imp. qts.)
| Hypoid gear oil API GL-5 or equivalent
| 4WD (for LSD)
| Hypoid gear oil LSD API GL-5 or equivalent
|
LUBRICANT / Rear differential (TSAM made)Item
| Capacity
| Oil grade
| Classification
| 2WD and made for DANA
| 2.30 to 2.40 liters (2.43 to 2.54 US qts, 2.02 to 2.11 Imp. qts.)
| Hypoid gear oil API GL-5 or equivalent
| Above-18°C (0°F): SAE 90 Below-18°C (0°F): SAE 85W-90
| 4WD and Pre-runner
| 2.40 to 2.50 liters (2.54 to 2.64 US qts, 2.11 to 2.20 Imp. qts.)
| 2WD (for LSD)
| 3.15 to 3.25 liters (3.30 to 3.43 US qts, 2.77 to 2.86 Imp. qts.)
| Hypoid gear oil LSD API GL-5 or equivalent
| 4WD (for LSD)
| 3.30 to 3.40 liters (3.49 to 3.59 US qts, 2.90 to 2.99 Imp. qts.)
| w/ Differential lock
| 2.85 to 2.95 liters (3.01 to 3.12 US qts, 2.51 to 2.60 Imp. qts.)
| Hypoid gear oil API GL-5 or equivalent
| 2 Pinion type
| 2.90 to 3.00 liters (3.07 to 3.17 US qts, 2.55 to 2.64 Imp. qts.)
| |
|
RECOMMENDED TOOLS
| 09011-12301
| Socket Wrench 30 mm
| -
| 
| 09031-00030
| Pin Punch
| -
| 
| 09044-00010
| Torx Socket E14
| -
| 
| 09905-00012
| Snap Ring No.1 Expander
| -
| 
| 09905-00013
| Snap Ring Pliers
| -
| - HINT:
- "Torx" is a registered trademark of Textron Inc.
|
|
SSMToyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
| -
| Toyota Genuine Seal Packing 1281 Three Bond 1281 or equivalent
| -
| Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
| -
| |
|