Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK ECM (for 1GR-FE)

G035613E02

  1. Disconnect the E14, E15 and E17 ECM connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E14-3 (BATT) - E17-1 (E1)
    L - BR
    Battery
    Always
    11 to 14 V
    E14-9 (IGSW) - E17-1 (E1)
    B-O - BR
    IG power supply
    Ignition switch ON
    11 to 14 V
    E14-9 (IGSW) - E17-1 (E1)
    B-O - BR
    IG power supply
    Ignition switch off
    Below 1 V
    E17-1 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E15-28 (E2) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E14, E15 and E17 ECM connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E14-15 (STP) - E17-1 (E1)
    G-W - BR
    Stop light switch input signal
    Ignition switch ON
    Brake pedal released
    Below 1 V
    E14-15 (STP) - E17-1 (E1)
    G-W - BR
    Stop light switch input signal
    Ignition switch ON
    Brake pedal depressed
    11 to 14 V
    E14-16 (ST1-) - E17-1 (E1)
    R-L - BR
    Cruise cancel input signal
    Ignition switch ON
    Brake pedal depressed
    Below 1 V
    E14-16 (ST1-) - E17-1 (E1)
    R-L - BR
    Cruise cancel input signal
    Ignition switch ON
    Brake pedal released
    11 to 14 V
    E13-2 (CCS) - E17-1 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    11 to 14 V
    E13-2 (CCS) - E17-1 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    CANCEL switch held on
    6.6 to 10.1 V
    E13-2 (CCS) - E17-1 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    (-SET)*1 (SET / COAST)*2 switch held on
    4.5 to 7.1 V
    E13-2 (CCS) - E17-1 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    (+RES)*1 (RES / ACC)*2 switch held on
    2.3 to 4.0 V
    E13-2 (CCS) - E17-1 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    Main switch on
    Below 1 V
    E13-18 (PI) - E17-1 (E1)
    L-B - BR
    Cruise main indicator light input signal
    Ignition switch ON
    Main switch on
    Below 1 V
    E13-18 (PI) - E17-1 (E1)
    L-B - BR
    Cruise control main switch signal
    Ignition switch ON
    Main switch on
    11 to 14 V
    E13-21 (D) - E17-1 (E1)*3
    G-W - BR
    Clutch signal
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    E13-21 (D) - E17-1 (E1)*3
    G-W - BR
    Clutch signal
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    E14-23 (TC) - E17-1 (E1)
    P-B - BR
    Terminal TC of DLC3
    Ignition switch ON
    9 to 14 V
    *1: w/ Multi-display
    *2: w/o Multi-display
    *3: for Manual Transmission
    If the result is not as specified, the ECM may have a malfunction.


CHECK ECM (for 1KD-FTV)

E110509E06

  1. Disconnect the E5, E6, E7 and E8 ECM connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E6-2 (BATT) - E7-7 (E1)
    L - BR
    Battery
    Always
    11 to 14 V
    E5-9 (IGSW) - E7-7 (E1)
    B-O - BR
    IG power supply
    Ignition switch ON
    11 to 14 V
    E5-9 (IGSW) - E7-7 (E1)
    B-O - BR
    IG power supply
    Ignition switch off
    Below 1 V
    E7-7 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E8-28 (E2) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E5, E6, E7 and E8 ECM connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E6-15 (STP) - E7-7 (E1)
    G-W - BR
    Stop light switch input signal
    Ignition switch ON
    Brake pedal released
    Below 1 V
    E6-15 (STP) - E7-7 (E1)
    G-W - BR
    Stop light switch input signal
    Ignition switch ON
    Brake pedal depressed
    11 to 14 V
    E6-14 (ST1-) - E7-7 (E1)
    R-L - BR
    Cruise cancel input signal
    Ignition switch ON
    Brake pedal depressed
    Below 1 V
    E6-14 (ST1-) - E7-7 (E1)
    R-L - BR
    Cruise cancel input signal
    Ignition switch ON
    Brake pedal released
    11 to 14 V
    E5-21 (CCS) - E7-7 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    11 to 14 V
    E5-21 (CCS) - E7-7 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    CANCEL switch held on
    6.6 to 10.1 V
    E5-21 (CCS) - E7-7 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    (-SET)*1 (SET / COAST)*2 switch held on
    4.5 to 7.1 V
    E5-21 (CCS) - E7-7 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    (+RES)*1 (RES / ACC)*2 switch held on
    2.3 to 4.0 V
    E5-21 (CCS) - E7-7 (E1)
    G-W - BR
    Cruise control main switch signal
    Ignition switch ON
    Main switch on
    Below 1 V
    E6-3 (PI) - E7-7 (E1)
    L-B - BR
    Cruise main indicator light input signal
    Ignition switch ON
    Main switch on
    Below 1 V
    E6-3 (PI) - E7-7 (E1)
    L-B - BR
    Cruise control main switch signal
    Ignition switch ON
    Main switch off
    11 to 14 V
    E6-10 (CLSW) - E7-7 (E1)*3
    G-W - BR
    Clutch signal
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    E6-10 (CLSW) - E7-7 (E1)*3
    G-W - BR
    Clutch signal
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    E5-11 (TC) - E7-7 (E1)
    P-B - BR
    Terminal TC of DLC3
    Ignition switch ON
    9 to 14 V
    *1: w/ Multi-display
    *2: w/o Multi-display
    *3: for Manual Transmission
    If the result is not as specified, the ECM may have a malfunction.