Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends signals to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Then terminal CCS of the ECM receives the voltage according to the switch condition.

WIRING DIAGRAM


E173933E02


E171159E04


INSPECTION PROCEDURE

1.CHECK VEHICLE CONTROL SYSTEM
  1. Check vehicle system.
    Result 
    Result
    Proceed to
    w/ Multi-display
    A
    w/o Multi-display
    B



B
Go to step 7
A


2.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)


    E149007E02
  1. Using the intelligent tester, read the Data List.

    Cruise Control 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    CCS Main SW M-CPU
    Cruise control main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -SET switch signal / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    +RES switch signal / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -

    OK:
    The intelligent tester display changes according to operation of cruise control main switch.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

3.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY

E149006E03

  1. Remove the cruise control main switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 3
    Neutral
    10 kΩ or higher
    Pushed to +RES
    235 to 245 Ω
    Pushed to -SET
    617 to 643 Ω
    Pushed to CANCEL
    1509 to 1571 Ω
    Main switch pushed off
    10 kΩ or higher
    Main switch pushed on
    Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH ASSEMBLY
OK


4.INSPECT CRUISE CONTROL SWITCH WIRE
E149008E06
  1. Remove the cruise control switch wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - B-3
    Always
    Below 1 Ω
    A-4 - B-1



NG
REPLACE CRUISE CONTROL SWITCH WIRE
OK


5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
E158922E04
  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - 1 (CCS)
    Always
    Below 1 Ω
    A-4 - 2 (ECC)
    Always
    Below 1 Ω



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
E171082E01
  1. Disconnect the S13 spiral cable connector.

  1. Disconnect the E13*1 or E5*2 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    S13-1 (CCS) - E13-2 (CCS)
    Always
    Below 1 Ω
    S13-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S13-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    S13-1 (CCS) - E5-21 (CCS)
    Always
    Below 1 Ω
    S13-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S13-1 (CCS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

7.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)


    E170811E02
  1. Using the intelligent tester, read the Data List.

    Cruise Control 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    CCS Main SW M-CPU
    Cruise control main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    SET / COAST switch signal / ON or OFF
    ON: SET / COAST switch on
    OFF: SET / COAST switch off
    -
    RES/ACC Switch
    RES / ACC switch signal / ON or OFF
    ON: RES / ACC switch on
    OFF: RES / ACC switch off
    -

    OK:
    The intelligent tester display changes according to operation of cruise control main switch.



NG
Go to step 8
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

8.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY
E171632E01
  1. Remove the cruise control main switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Neutral
    10 kΩ or higher
    Pushed to RES / ACC
    235 to 245 Ω
    Pushed to SET / COAST
    617 to 643 Ω
    Pushed to CANCEL
    1509 to 1571 Ω
    Main switch pushed off
    10 kΩ or higher
    Main switch pushed on
    Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH ASSEMBLY
OK


9.INSPECT SPIRAL CABLE SUB-ASSEMBLY
E171079E03
  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 1 (CCS)
    Always
    Below 1 Ω
    4 - 2 (ECC)
    Always
    Below 1 Ω



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


10.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
E171082E01
  1. Disconnect the S13 spiral cable connector.

  1. Disconnect the E13*1 or E5*2 ECM connector.
    *1: for 1GR-FE
    *2: for 1KD-FTV

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    S13-1 (CCS) - E13-2 (CCS)
    Always
    Below 1 Ω
    S13-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S13-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    S13-1 (CCS) - E5-21 (CCS)
    Always
    Below 1 Ω
    S13-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S13-1 (CCS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE