DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0617 | When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Positions | Starter Signal |
| ON | OFF |
| START | ON |
| Result | Proceed to |
| OK | A |
| NG | B (M/T Model) |
| NG | C (A/T Model) |
|
| ||||
|
| ||||
| C | |
| 2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the N1 PNP switch connector.
Measure the resistance when the transmission gear selector lever is moved to each position.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| Except P and N | 4 - 5 | 10 kΩ or higher |
| P | 2 - 5 | 10 kΩ or higher |
| R | ||
| N | ||
| D | ||
| 2 | ||
| L |
Reconnect the PNP switch connector.
|
| ||||
| NG | |
| 3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Positions | Starter Signal |
| ON | OFF |
| START | ON |
|
| ||||
| NG | |
| 5.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the I6 ignition switch connector.
Measure the resistance of the ignition switch.
| Tester Connection | Ignition Switch Position | Specified Condition |
| AM2 (5) - ST2 (7) | OFF | 10 kΩ or higher |
| AM2 (5) - ST2 (7) | START | Below 1 Ω |
Reconnect the ignition switch connector.
|
| ||||
| NG | |
| 6.REPLACE IGNITION SWITCH ASSEMBLY |
| NEXT | |
| 7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Positions | Starter Signal |
| ON | OFF |
| START | ON |
|
| ||||
| NG | |
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Clear DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0617 | A |
| No DTC | B |
|
| ||||
| A | ||
| ||