Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

ECD SYSTEM (w/ EGR Cooler) > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A154777E01


INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK ECM (+B VOLTAGE)


    A154583E15
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-1 (+B) - E7-7 (E1)
    11 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
NG


2.CHECK WIRE HARNESS (ECM - BODY GROUND)


    A065745E87
  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E7-7 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


3.CHECK ECM (IGSW VOLTAGE)


    A154583E17
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-9 (IGSW) - E7-7 (E1)
    11 to 14 V



OK
Go to step 6
NG


4.INSPECT FUSE (IGN FUSE)


    A155929E01
  1. Remove the IGN fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


5.INSPECT IGNITION SWITCH ASSEMBLY


    A056879E52
  1. Disconnect the I6 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 6 (IG2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 6 (IG2)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM) 

6.CHECK ECM (MREL VOLTAGE)


    A154583E18
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-8 (MREL) - E7-7 (E1)
    11 to 14 V



NG
REPLACE ECM
OK


7.INSPECT FUSE (EFI FUSE)


    A099789E11
  1. Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL)
OK


8.INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY)


    G039047E14
  1. Remove the integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J integration relay connector.

  1. Measure the voltage of the MAIN relay.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1J-4 - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 10
OK


9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)
  1. Remove the integration relay from the engine room junction block (Click here).



    G034918E06
  1. Disconnect the 1J integration relay connector from the engine room junction block.

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    1J-4 - E5-1 (+B)
    Below 1 Ω
    1J-3 - Body ground
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    1J-4 or E5-1 (+B) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL) 

10.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM, INTEGRATION RELAY (MAIN RELAY) - BODY GROUND)


    G034918E05
  1. Remove the integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J integration relay connector from the engine room junction block.

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    1J-2 - E5-8 (MREL)
    Below 1 Ω
    1J-3 - Body ground
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    1J-2 or E5-8 (MREL) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)
OK

REPLACE INTEGRATION NO.1 RELAY