Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here



When using intelligent tester, troubleshoot according to procedures below

HINT:
*: Use the intelligent tester.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS

      NEXT


      3.INSPECT BATTERY VOLTAGE

        Standard voltage:
        11 to 14 V

        If the voltage is below 11 V, recharge or replace the battery before proceeding.

      NEXT


      4.CONNECT INTELLIGENT TESTER TO DLC3*

        NEXT


        5.CHECK AND CLEAR DTC AND FREEZE FRAME DATA*

          NEXT


          6.VISUAL INSPECTION

            NEXT


            7.SETTING CHECK MODE DIAGNOSIS*
            1. Refer to the check mode procedure (Click here).


            NEXT


            8.PROBLEM SYMPTOM CONFIRMATION
            1. Refer to the road test (Click here).

              Result:
              Result
              Proceed to
              Symptom does not occur
              A
              Symptom occurs
              B



            B.
            GO TO STEP 10
            A


            9.SYMPTOM SIMULATION
            1. Refer to the electronic circuit inspection procedure (Click here).


            NEXT


            10.DTC CHECK*
            1. Refer to the DTC check / clear (Click here).

            2. Result:
              Result
              Proceed to
              DTC is not output
              A
              DTC is output
              B



            B.
            GO TO STEP 19
            A


            11.BASIC INSPECTION
            1. Refer to the automatic transmission fluid (Click here).

            2. Refer to the park / neutral position switch (Click here).

            3. Refer to the floor shift assembly (Click here).



            NG.
            GO TO STEP 20
            OK


            12.MECHANICAL SYSTEM TEST
            1. Refer to the mechanical system test (Click here).



            NG.
            GO TO STEP 17
            OK


            13.HYDRAULIC TEST
            1. Refer to the hydraulic test (Click here).



            NG.
            GO TO STEP 17
            OK


            14.MANUAL SHIFTING TEST
            1. Refer to the manual shifting test (Click here).



            NG.
            GO TO STEP 16
            OK


            15.PROBLEM SYMPTOMS TABLE CHAPTER 1
            1. Refer to the problem symptoms table (Click here).



            NG.
            GO TO STEP 20
            OK


            16.PROBLEM SYMPTOMS TABLE CHAPTER 2
            1. Refer to the problem symptoms table (Click here).



            NG.
            GO TO STEP 18
            OK


            17.PROBLEM SYMPTOMS TABLE CHAPTER 3
            1. Refer to the problem symptoms table (Click here).


            NG


            18.PART INSPECTION


              NG.
              GO TO STEP 20
              OK


              19.DTC CHART
              1. Refer to the diagnostic trouble code chart (Click here).


              NEXT


              20.CIRCUIT INSPECTION

                NEXT


                21.REPAIR OR REPLACE

                  NEXT


                  22.CONFIRMATION TEST

                    NEXT

                    END


                    When not using intelligent tester, troubleshoot according to procedures below


                    1.VEHICLE BROUGHT TO WORKSHOP

                      NEXT


                      2.CUSTOMER PROBLEM ANALYSIS

                        NEXT


                        3.INSPECT BATTERY VOLTAGE

                          Standard voltage:
                          11 to 14 V

                          If the voltage is below 11 V, recharge or replace the battery before proceeding.

                        NEXT


                        4.CHECK AND CLEAR DTC

                          NEXT


                          5.PROBLEM SYMPTOM CONFIRMATION

                            Result:
                            Result
                            Proceed to
                            Symptom does not occur
                            A
                            Symptom occurs
                            B



                          B.
                          GO TO STEP 7
                          A


                          6.SYMPTOM SIMULATION

                            NEXT


                            7.DTC CHECK

                              Result:
                              Result
                              Proceed to
                              DTC is not output
                              A
                              DTC is output
                              B



                            B.
                            GO TO STEP 16
                            A


                            8.BASIC INSPECTION


                              NG.
                              GO TO STEP 17
                              OK


                              9.MECHANICAL SYSTEM TEST


                                NG.
                                GO TO STEP 14
                                OK


                                10.HYDRAULIC TEST


                                  NG.
                                  GO TO STEP 14
                                  OK


                                  11.MANUAL SHIFTING TEST


                                    NG.
                                    GO TO STEP 13
                                    OK


                                    12.PROBLEM SYMPTOMS TABLE CHAPTER 1


                                      NG.
                                      GO TO STEP 17
                                      OK


                                      13.PROBLEM SYMPTOMS TABLE CHAPTER 2


                                        NG.
                                        GO TO STEP 15
                                        OK


                                        14.PROBLEM SYMPTOMS TABLE CHAPTER 3

                                          NG


                                          15.PART INSPECTION


                                            NG.
                                            GO TO STEP 18
                                            OK


                                            16.DTC CHART

                                              NEXT


                                              17.CIRCUIT INSPECTION

                                                NEXT


                                                18.REPAIR OR REPLACE

                                                  NEXT


                                                  19.CONFIRMATION TEST

                                                    NEXT

                                                    END