AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and push the tester main switch on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Follow the instructions on the tester and read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| SPD (NC0) | Input turbine speed/ Min.: 0 rpm Max.: 12750 rpm |
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| Neutral Position SW Signal | Park/neutral position switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ ON or OFF | Brake pedal is
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd or 4th | Shift position is:
| - |
| Shift SW Status (R Range) | Park/neutral position switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (3 Range) | Park/neutral position switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (2 Range) | Park/neutral position switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (L Range) | Park/neutral position switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| A/T Oil Temperature 3 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited |
| Lock Up | Lock-up/ ON or OFF | Lock-up is:
| - |
| Lock Up Solenoid Status | Lock-up solenoid status/ ON or OFF | Lock-up solenoid is:
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and push the tester main switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate the shift solenoid S1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate the shift solenoid S2 | ON or OFF | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid SL to set automatic transmission to lock-up condition | ON or OFF | Possible to check shift solenoid valve SL operation [Vehicle Condition] Vehicle speed: 60 km/h (36 mph) or more |
| Activate the Solenoid (SL) | Operate the shift solenoid SL | ON or OFF | [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |