Home › TRANSMISSION ยท A340F AUTOMATIC TRANSMISSION › ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM

ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the intelligent tester ON.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. Follow the instructions on the tester and read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on speedometer
    Engine Speed
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    Engine idling: 700 to 800 rpm
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%
    Max.: 100%
    Running without load (2500 rpm): 13.1 to 18.9%
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    After warming up engine: 80 to 90°C (176 to 194°F)
    1. If the value is -40°C (-40°F), the sensor circuit is open.
    2. If the value is 140°C (284°F), the sensor circuit is shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 seconds,
    Max.: 65535 seconds
    Time after engine start
    -
    Battery Voltage
    Battery voltage/
    Min.: 0 V
    Max.: 65.535 V
    Engine idling: 11 to 14 V
    -
    Starter Signal
    Starter signal/
    ON or OFF
    1. ON: Engine cranking
    2. OFF: Engine not cranking
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever is:
    On P or N: ON
    Not on P or N: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, Click here, Click here

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. Brake pedal is depressed: ON
    2. Brake pedal is released: OFF
    -
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    -
    SPD Test Result
    Check mode result for vehicle/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Heater Monitor
    Heated oxygen sensor (air fuel ratio sensor) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    Heated oxygen sensor (air fuel ratio sensor) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    Heated oxygen sensor (air fuel ratio sensor) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    Heated oxygen sensor (air fuel ratio sensor) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    # Codes (Include History)
    # of Codes/
    Min.: 0
    Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Distance after DTC stored
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 minutes,
    Max.: 65535 minutes
    Equivalent to running time after MIL turns on
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 minutes,
    Max.: 65535 minutes
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Equivalent to distance driven after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTCs cleared
    Number of Emission DTC
    Number of emission DTCs
    -
    -
    Model Code
    Model Code/
    -
    -
    Engine Type
    Engine Type/
    -
    -
    Cylinder Number
    Cylinder number/
    -
    -
    Destination
    Destination/
    -
    -
    Model Year
    Model year/
    -
    -
    Engine Speed from EFI
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    -
    Engine speed received from the ECM.
    Intake-Air Temp from EFI
    Intake air temperature/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    -
    Intake air temperature received from the ECM.
    Coolant Temp from EFI
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    -
    Coolant temperature received from the ECM.
    Accel Position from EFI
    Absolute accelerator pedal position/
    Min.: 0%
    Max.: 100%
    -
    -
    Injection Volume from EFI
    Injection volume/
    Min.: -10 mm3
    Max.: 1,279.98 mm3
    -
    -
    SPD (NC0)
    Input turbine speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up ON (warmed up engine, other than O/D):
      Input turbine speed (NC0) is equal to the engine speed
    2. Lock-up ON (warmed up engine, O/D):
      Input turbine speed (NC0) is 0 rpm
    3. Lock-up OFF (idling with shift lever on N):
      Input turbine speed (NC0) is nearly equal to engine speed
    -
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)
    (output shaft speed is equal to vehicle speed)
    -
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    On R: ON
    Not on R: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, Click here, Click here

    Shift SW Status (2 Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    On 2: ON
    Not on 2: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, Click here, Click here

    Shift SW Status (L Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    On L: ON
    Not on L: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, Click here, Click here

    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    On D: ON
    Not on D: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, Click here, Click here

    Shift SW Status (3 Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    On 3: ON
    Not on 3: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, Click here, Click here

    A/T Oil Temperature 3
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature during engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited
    Lock Up
    Lock-up/
    ON or OFF
    1. ON: Lock-up operating
    2. OFF: Lock-up not operating
    -
    Lock Up Solenoid Status
    Lock-up solenoid status/
    ON or OFF
    1. Lock-up: ON
    2. Not on lock-up: OFF
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd or 4th (O/D)
    Shift lever position is:
    1. On L: 1st
    2. On 2: 1st or 2nd
    3. On D (O/D OFF): 1st, 2nd or 3rd
    4. On D (O/D ON): 1st, 2nd, 3rd or 4th (O/D)
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the intelligent tester ON.

  4. Enter the following menus: Powertrain / ECT / Active Test.

  5. Perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON or OFF
    -
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate shift solenoid valve S1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (S2)
    Operate shift solenoid valve S2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Lock Up
    Control shift solenoid valve SLT to set automatic transmission to lock-up
    ON or OFF
    Possible to check shift solenoid valve SLT operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (37 mph) or more
    Activate the Solenoid (SL)
    Operate shift solenoid valve SL
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Control the Shift Position
    Operate shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (31 mph) or less

    HINT:
    *: "Control the Line Pressure Up" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.