Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)

DTC    P0976    Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)

DTC    P0977    Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2)

for Preparation Click here


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which is controlled by the TCM. If an open or short circuit occurs in the shift solenoid valves, the TCM controls the remaining normal shift solenoid valve to allow the vehicle to be operated safely (Click here).

DTC Code
DTC Detection Condition
Trouble Area
P0976
TCM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1 trip detection logic)
  1. Short in shift solenoid valve S2 circuit
  2. Shift solenoid valve S2
  3. TCM
P0977
TCM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1 trip detection logic)
  1. Open in shift solenoid valve S2 circuit
  2. Shift solenoid valve S2
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S2 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. When the shift solenoid valve S2 is ON, if resistance is 8 Ω or less, the TCM determines that there is a short in the shift solenoid valve S2 circuit.
When the shift solenoid valve S2 is OFF, if resistance is 100 kΩ or more, the TCM determines that there is an open in the shift solenoid valve S2 circuit (Click here).

WIRING DIAGRAM


C161204E51


INSPECTION PROCEDURE


HINT:
The shift solenoid valve S2 turns ON/OFF normally when the shift lever is on D:

TCM gear shift command
1st
2nd
3rd
4th
5th
Shift solenoid valve S2
OFF
ON
ON
OFF
OFF

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S2)


    C159421E49
  1. Disconnect the E1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    15 - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)


    C191544E28
  1. Disconnect the T19 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-17 (S2) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM 

3.INSPECT SHIFT SOLENOID VALVE S2


    A110987E08
  1. Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S2 connector
    2. Battery negative (-) → Shift solenoid valve S2 body
    Valve moves and makes an operating noise



NG
REPLACE SHIFT SOLENOID VALVE S2
OK

REPAIR OR REPLACE TRANSMISSION WIRE