VEHICLE STABILITY CONTROL SYSTEM > FREEZE FRAME DATA |
| FREEZE FRAME DATA |
Whenever an ABS DTC is detected, the skid control ECU stores the current vehicle (sensor) state as Freeze Frame Data.
The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to on since the last time the ABS was activated.
| CHECK FREEZE FRAME DATA |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
According to the display on the tester, select the DTC data display with Freeze Frame Data.
| Tester Display | Measurement Item | Reference Value |
| Elapsed Time after Freeze Trigger | Elapsed time after freeze frame trigger | Min.: 0 ms Max.: 500 ms |
| Number of IG ON | Number of operations of ignition switch being turned on after storing Freeze Frame Data | 0 to 31 |
| Buzzer | Skid control buzzer signal | Skid control buzzer ON: ON Skid control buzzer OFF: OFF |
| Stop Light SW | Stop light switch signal | Stop light switch ON: ON Stop light switch OFF: OFF |
| Parking Brake SW | Parking brake switch signal | Parking brake switch ON: ON Parking brake switch OFF: OFF |
| Gear Position | Gear position information | FAIL 1st 2nd 3rd 4th 5th 6th 7th 8th P, N R NOT R |
| Shift Lever Position | Shift lever position information | FAIL 1st 2nd 3rd 4th 5th 6th/B D/M P, N R |
| Operated System | Operated system status | ABS: ABS activated VSC: VSC activated TRC: TRC activated BA: BA activated HAB: HAB activated PBA: PBA activated PB: PB activated HA-CTRL: Hill-start assist control activated FAIL: Fail-safe mode activated SYS: System prohibit activated NON: No operation activated |
| Master Cylinder Sensor | Master cylinder pressure sensor reading | Min.: 0 V Max.: 5 V |
| M/C Sensor Grade | Master cylinder pressure sensor change | Min.: -30 MPa/s Max.: 225 MPa/s |
| Yaw Rate Sensor | Yaw rate sensor reading | Min.: -128 deg/s Max.: 127 deg/s |
| Lateral G | Lateral acceleration | Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
| Forward and Rearward G | Forward and backward acceleration | Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
| FR Wheel Speed | Front wheel RH speed | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202.8 mph) |
| FL Wheel Speed | Front wheel LH speed | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202.8 mph) |
| RR Wheel Speed | Rear wheel RH speed | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202.8 mph) |
| RL Wheel Speed | Rear wheel LH speed | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202.8 mph) |
| Vehicle Speed | Vehicle speed reading | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202.8 mph) |
| Vehicle Speed Grade | Vehicle acceleration | Min.: -25.11 m/s2
Max.: 24.91 m/s2 |
| Real Engine Torque | Real engine torque | Min.: -1024 Nm Max.: 1023 Nm |
| Accelerator Opening Angle % | Throttle valve opening angle as a percentage | Min.: 0% Max.: 128% |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch signal | Brake pedal load sensing switch ON: ON Brake pedal load sensing switch OFF: OFF |
| Inspection Mode | Inspection mode | Other: Normal mode Inspect: Inspection mode |
| Steering Angle Sensor | Steering angle sensor reading | Min.: -3276.8 deg Max.: 3276.7 deg |
| TRC/VSC Off Mode | TRC/VSC off mode | Normal: Normal mode TRC OFF: TRC off mode VSC OFF: VSC off mode |
| CLEAR FREEZE FRAME DATA |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs and Freeze Frame Data (Click here).