DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 | Open in the circuit between terminals AF+ and AF- of the A/F sensor while engine is running (2 trip detection logic) |
|
| P2238 |
|
|
| P2239 |
|
|
| P2252 | AF- is 0.5 V or less for 5.0 seconds or more |
|
| P2253 | AF- is more than 4.5 V for 5.0 seconds or more |
|
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B1 S1 (A/F) | +25% | Rich | Less than 3.0 V |
| AFS B1S1 or AFS B1 S1 (A/F) | -12.5% | Lean | More than 3.35 V |
| O2S B1 S2 (HO2) | +25% | Rich | More than 0.55 V |
| O2S B1 S2 (HO2) | -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Areas | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK WIRE HARNESS (A/F SENSOR - ECM) |
![]() |
Disconnect the A18 A/F sensor connector.
Turn the E12 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A18-1 (HT1A) - E12-1 (HA1A) | Below 1 Ω |
| A18-3 (A1A+) - E12-21 (A1A+) | Below 1 Ω |
| A18-4 (A1A-) - E12-31 (A1A-) | Below 1 Ω |
| A18-1 (HT1A) or E12-1 (HA1A) - Body ground | 10 kΩ or higher |
| A18-3 (A1A+) or E12-21 (A1A+) - Body ground | 10 kΩ or higher |
| A18-4 (A1A-) or E12-31 (A1A-) - Body ground | 10 kΩ or higher |

|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor.
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs.
Start the engine.
Allow the engine idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P2237, P2238, P2239, P2252 or P2253 is output | B |
|
| ||||
| A | ||
| ||