WIRELESS DOOR LOCK CONTROL SYSTEM (for Built-in Type Door Control Receiver) > TERMINALS OF ECU |
| CHECK THEFT WARNING ECU ASSEMBLY |

Disconnect the T16 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E (T16-1) - Body ground | B-W -Body ground | Ground | Always | Below 1 Ω |
| IG (T16-4) - E (T16-1) | R-L - B-W | Ignition power supply | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 10 to 14 V | |||
| +B1 (T16-3) -E (T16-1) | L-Y B-W | +B (ECU-B) power source | Always | 10 to 14 V |
| +B2 (T16-12) - E (T16-1) | LG - B-W | +B (DOOR) power source | Always | 10 to 14 V |
| L2 (T16-20) - Body ground | L - Body ground | Door control switch (master switch) lock output | Door control switch (master switch) LOCK | 10 kΩ or higher |
| Door control switch (master switch) OFF | Below 1 Ω | |||
| UL3 (T16-21) -Body ground | L-W - Body ground | Door control switch (master switch) unlock output | Door control switch UNLOCK | 10 kΩ or higher |
| Door control switch OFF | Below 1 Ω | |||
| CTY (T16-7) - Body ground | R-L - Body ground | All door courtesy switches | All doors are closed | 10 kΩ or higher |
| One or more doors are open | Below 1 Ω | |||
| KSW (T16-5) - Body ground | G-Y - Body ground | Unlock warning switch | No key in ignition key cylinder | 10 kΩ or higher |
| Key inserted in ignition key cylinder | Below 1 Ω |
Reconnect the T16 ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| HAZD (T16-23) - Body ground | G-O -Body ground | Hazard warning lights signal output | Hazard warning lights OFF | Below 1 V |
| Hazard warning lights ON | Pulse generation | |||
| SH- (T16-26) - Body ground | B - Body ground | Security horn signal output | Security horn OFF | Below 1 V |
| Security horn ON | Pulse generation |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (INTEGRATION RELAY) |

Disconnect the 2A, 2D, 2L and 2R junction block connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (2D-9) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| BECU (2L-12) - GND (2D-9) | L - W-B | +B (ECU - B) power source | Always | 10 to 14 V |
| L1 (2A-4) - Body ground | L - Body ground | Door control switch (master switch) lock input | Door control switch (master switch) LOCK | 10 kΩ or higher |
| Door control switch (master switch) OFF | Below 1 Ω | |||
| UL1 (2D-4) - Body ground | L-W - Body ground | Door control switch (master switch) unlock input | Door control switch (master switch) UNLOCK | 10 kΩ or higher |
| Door control switch (master switch) OFF | Below 1 Ω | |||
| DCTY (2O-27) - Body ground | R-B - Body ground | Driver side door courtesy switch | Driver side door closed | 10 kΩ or higher |
| Driver side door open | Below 1 Ω | |||
| 2O-25 - Body ground | R-L - Body ground | All door courtesy switches except driver side door | All doors are closed except driver side door | 10 kΩ or higher |
| One or more doors open except driver side door | Below 1 Ω |
Reconnect the 2A, 2D, 2L and 2R junction block connectors.
Measure the voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| ACT+ (2R-28) - Body ground | L - Body ground | Door lock motor LOCK drive output (driver side door) | Door control switch (master switch) or driver side door key cylinder OFF | Below 1 V |
| Door control switch (master switch) or driver side door key cylinder LOCK | 10 to 14 V | |||
| ACT- (2R-27) - Body ground | L-Y - Body ground | Door lock motor UNLOCK drive output (driver side door) | Door control switch (master switch) or driver side door key cylinder OFF | Below 1 V |
| Door control switch (master switch) or driver side door key cylinder UNLOCK | 10 to 14 V |