Home › BODY › SEAT › FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)

FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.



1. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    B087768E01
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE FRONT SEAT CUSHION SHIELD LH


    B211021E02
  1. Remove the 2 screws.

  1. Detach the rear part of the cushion shield in the order shown in the illustration, and then detach the claw and remove the cushion shield.



3. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)


B087811E01
  1. w/ Driver seat belt warning light:
    Detach the clamp.



    B089297E01
  1. w/ Driver seat belt warning light:
    Detach the wire harness from the clamp.

  1. Remove the nut and seat belt.

  1. Remove the buckle cover.



4. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)


B113100E01
  1. w/ Passenger seat belt warning light:
    Detach the 2 clamps.

  1. w/ Passenger seat belt warning light:
    Disconnect the connector.



    B087812E02
  1. Detach the wire harness from the clamp.

  1. Remove the nut and seat belt.

  1. Remove the buckle cover.



5. REMOVE FRONT SEAT CUSHION COVER LH
  1. Remove the seat cushion cover.



6. REMOVE FRONT SEAT CUSHION INNER SHIELD LH


B086035E02
  1. Remove the 2 screws.

  1. Detach the rear part of the inner shield in the order shown in the illustration, and then remove the cushion shield.



7. REMOVE VERTICAL SEAT ADJUSTER KNOB RH (for RHD, w/ Vertical Adjuster)


B084948E02
  1. Using a screwdriver, remove the snap ring as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the knob.



8. REMOVE SEATBACK SPRING
  1. Remove the seatback spring.



9. REMOVE SEAT CUSHION COVER WITH PAD


B190019E03
  1. Detach the wire harness clamps.

  1. Detach the 2 hooks.

  1. Detach the hooks in the hook area shown in the illustration.

  1. Remove the hog rings and seat cushion cover with pad from the seat cushion frame.



10. REMOVE FRONT SEAT CUSHION PROTECTOR


    B207791
  1. Remove the 2 protectors.



11. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    B207624
  1. Remove the hog rings and seat cushion cover.



12. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)


    B122838E02
  1. Cut off the tack pins which fasten the seat heater, and then remove the front seat cushion heater from the seat cushion cover.

    NOTICE:
    Be careful not to damage the seat cushion cover.



13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    B207788
  1. Remove the hog rings from the wires of the seatback cover. Then roll up the seatback cover.



    B209094
  1. Remove the hog rings and detach the strap of the seatback cover. Then roll up the seatback cover.



    B257946
  1. Remove the hog rings from the center of the seatback pad and roll up the seatback cover.



    B131236
  1. Remove the nut and detach the seatback cover bracket.



    B207581
  1. Remove the hog rings from the upper part of the seatback pad. Then roll up the seatback cover.



    B207089
  1. Detach the 4 claws and remove the 2 headrest supports.



    B207625
  1. Remove the hog rings and seatback cover.



14. REMOVE SEPARATE TYPE FRONT SEATBACK PAD


    B207090
  1. Remove the seatback pad.



15. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)


    B122836E02
  1. Cut off the tack pins which fasten the seat heater, and then remove the front seatback heater from the seatback cover.

    NOTICE:
    Be careful not to damage the seat cushion cover.



16. REMOVE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY


    B213584
  1. w/ Seat Heater system:
    Detach the wire harness clamps.



    B213444
  1. Detach the wire harness clamps.

  1. Remove the 4 bolts and seat cushion frame.



17. REMOVE VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (for RHD, w/ Vertical Adjuster)


B086128E02
  1. Using a screwdriver, detach the seat spring from the reclining adjuster lower arm.

    HINT:
    Tape the screwdriver tip before use.



    B086127E02
  1. Using a screwdriver, spread apart the tabs that hold the spring, and then remove the spring.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a 6 mm socket hexagon wrench, remove the front seat No. 2 adjuster pin.



    B084958E01
  1. Temporarily install the vertical seat adjuster knob.

  1. Turn the knob counterclockwise and move the gear of the vertical adjusting shaft to the position shown in the illustration.

  1. Remove the vertical seat adjuster knob.



    B084964E01
  1. Using a screwdriver, remove the 2 E-rings and vertical adjusting shaft.



18. REMOVE SEAT TRACK HANDLE SUB-ASSEMBLY


    B084969E03
  1. Detach the spring of the seat track in the order shown in the illustration. Then remove the handle.



19. REMOVE FRONT SEAT ADJUSTER ROD (for RHD, w/ Vertical Adjuster)


    B209674
  1. Remove the 2 bolts and front seat adjuster rod.



20. REMOVE RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY LH


    B214331
  1. Remove the 2 bolts and reclining adjuster lower arm with front seat outer track.



    B084945E01
  1. for RHD, w/ Vertical Adjuster:
    Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and reclining adjuster lower arm.



    B214332
  1. w/o Vertical Adjuster:
    Remove the 3 bolts and reclining adjuster lower arm.



21. REMOVE RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY RH
  1. for RHD, w/ Vertical Adjuster:
    Use the same procedures described for the LH side.

  1. w/o Vertical Adjuster:
    Use the same procedures described for the LH side.



22. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR
  1. Remove the seat cushion edge protector.