FRONT SEAT ASSEMBLY (for Separate Seat Type) > DISASSEMBLY |
| 1. REMOVE VERTICAL SEAT ADJUSTER KNOB LH (w/ Vertical Adjuster) |
![]() |
Using a screwdriver, remove the snap ring as shown in the illustration. Then remove the knob.
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.
| 3. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the 2 screws.
Detach the rear part of the cushion shield in the order shown in the illustration, and then detach the claw and remove the cushion shield.
| 4. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) |
![]() |
w/ Driver seat belt warning light:
Detach the clamp.
![]() |
w/ Driver seat belt warning light:
Detach the wire harness from the clamp.
Remove the nut and seat belt.
Remove the buckle cover.
| 5. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) |
![]() |
w/ Passenger seat belt warning light:
Detach the 2 clamps.
w/ Passenger seat belt warning light:
Disconnect the connector.
![]() |
Detach the wire harness from the clamp.
Remove the nut and seat belt.
Remove the buckle cover.
| 6. REMOVE FRONT SEAT CUSHION SHIELD INNER LH |
![]() |
Remove the 2 screws.
Detach the rear part of the inner shield in the order shown in the illustration, and then remove the cushion shield.
| 7. REMOVE FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH (for Walk in Seat Type) |
Remove the fold seat lock control cable.
| 8. REMOVE FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH (for Walk in Seat Type) |
| 9. REMOVE SEAT TRACK CONTROL CABLE BRACKET LH (for Walk in Seat Type) |
![]() |
Using a screwdriver, remove the E-ring and bracket.
| 10. REMOVE SEAT TRACK CONTROL CABLE BRACKET RH (for Walk in Seat Type) |
| 11. REMOVE SEATBACK SPRING |
Remove the seatback spring.
| 12. REMOVE ADJUSTER TUBE (for Walk in Seat Type) |
Remove the adjuster tube from the seatback spring.
| 13. REMOVE FRONT SEATBACK ASSEMBLY |
w/ Seat Heater system:
Disconnect the seatback heater connector.
![]() |
Remove the 4 bolts and seatback.
| 14. REMOVE FRONT SEATBACK COVER |
![]() |
Remove the hog rings from the wires of the seatback cover. Then roll up the seatback cover.
![]() |
Remove the hog rings and detach the 2 straps of the seatback cover. Then roll up the seatback cover.
![]() |
for Normal Seat:
Remove the hog rings from the center of the seatback pad and roll up the seatback cover.
![]() |
for Leather Seat:
Remove the hog rings from the center of the seatback pad and roll up the seatback cover.
![]() |
Remove the hog rings from the upper part of the seatback pad. Then roll up the seatback cover.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
![]() |
Remove the hog rings and seatback cover.
| 15. REMOVE FRONT SEATBACK PAD |
![]() |
Remove the seatback pad.
| 16. REMOVE FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) |
![]() |
Cut off the tack pins which fasten the seat heater, and then remove the front seatback heater from the seatback cover.
| 17. REMOVE FRONT SEAT CUSHION COVER |
![]() |
w/ Occupant Detection Sensor, w/ Seat Heater System:
Detach the wire harness clamps.
Detach the 2 hooks.
Detach the hooks in the hook area shown in the illustration.
Remove the hog rings and seat cushion cover with pad from the seat cushion frame.
![]() |
for Normal Seat:
Remove the hog rings and seat cushion cover.
![]() |
for Leather Seat:
Remove the hog rings and seat cushion cover.
| 18. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) |
![]() |
Cut off the tack pins which fasten the seat heater, and then remove the front seat cushion heater from the seat cushion cover.
| 19. REMOVE FRONT SEAT CUSHION PROTECTOR |
![]() |
Remove the 2 protectors.
| 20. REMOVE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY |
![]() |
Remove the 4 bolts and seat cushion frame.
![]() |
w/ Seat Heater System:
Detach the wire harness clamps.
Remove the 4 bolts and seat cushion frame.
| 21. REMOVE VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (w/ Vertical Adjuster) |
![]() |
Using a screwdriver, detach the seat spring from the reclining adjuster lower arm.
![]() |
Using a screwdriver, spread apart the tabs that hold the spring, and then remove the spring.
Using a 6 mm socket hexagon wrench, remove the front seat No. 2 adjuster pin.
![]() |
Temporarily install the vertical seat adjuster knob.
Turn the knob clockwise and move the gear of the vertical adjusting shaft to the position shown in the illustration.
Remove the vertical seat adjuster knob.
![]() |
Using a screwdriver, remove the 2 E-rings and vertical adjusting shaft.
| 22. REMOVE SEAT TRACK ADJUSTING HANDLE |
![]() |
Detach the spring of the seat track in the order shown in the illustration. Then remove the handle.
| 23. REMOVE FRONT SEAT ADJUSTER ROD (w/ Vertical Adjuster) |
![]() |
Remove the 2 bolts and adjuster rod.
| 24. REMOVE RECLINING ADJUSTER ARM SUB-ASSEMBLY LOWER LH |
![]() |
w/ Vertical Adjuster:
Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and reclining adjuster arm.
![]() |
w/o Vertical Adjuster, for Walk in Seat Type:
Remove the 3 bolts and reclining adjuster arm.
| 25. REMOVE RECLINING ADJUSTER ARM SUB-ASSEMBLY LOWER RH |
w/ Vertical Adjuster:
Use the same procedures described for the LH side.
w/o Vertical Adjuster, for Walk in Seat Type:
Use the same procedures described for the LH side.
| 26. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR |
Remove the seat cushion edge protector.
| 27. REMOVE SEAT TRACK COVER SPRING (for Walk in Seat Type) |
![]() |
Remove the spring from the front seat outer track.