Home › BODY › SEAT › FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)

FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.



1. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR
  1. Install the seat cushion edge protector.



2. INSTALL RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY LH


    B084945E01
  1. for RHD, w/ Vertical Adjuster:
    Using a T40 "TORX" socket wrench, install the reclining adjuster arm with the 2 "TORX" bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    B214332
  1. w/o Vertical Adjuster:
    Install the reclining adjuster lower arm with the 3 bolts.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }



    B214331
  1. Install the reclining adjuster lower arm with front seat outer track with the 2 bolts.

    Torque:
    40 N*m{ 407 kgf*cm , 30 ft.*lbf }



3. INSTALL RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY RH
  1. for RHD, w/ Vertical Adjuster:
    Use the same procedures described for the LH side.

  1. w/o Vertical Adjuster:
    Use the same procedures described for the LH side.



4. INSTALL FRONT SEAT ADJUSTER ROD (for RHD, w/ Vertical Adjuster)


    B209674
  1. Install the adjuster rod with the 2 bolts.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }



5. INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY


    B108470E02
  1. Attach the spring of the seat track in the order shown in the illustration to install the handle.



6. INSTALL VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (w/ Vertical Adjuster)


    B108469
  1. Install the vertical adjusting shaft to the reclining adjuster arm with 2 new E-rings.



    B087784E04
  1. Temporarily install the vertical seat adjuster knob.

  1. Turn the knob as much as possible in the direction indicated by arrow A in the illustration.

  1. Mesh the gear of the vertical adjusting shaft with the gear of the reclining adjuster lower arm.

  1. Align the holes of the adjusting shaft and adjusting arm by turning the knob in the direction indicated by arrow B in the illustration.

  1. Remove the vertical seat adjuster knob.



    B087785E02
  1. Install the seat spring as shown in the illustration.

  1. Using pliers, push together the tabs that hold the spring.

  1. Using a 6 mm socket hexagon wrench, install the front seat No. 2 adjuster pin.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



7. INSTALL FRONT SEAT CUSHION FRAME SUB-ASSEMBLY


    B213444
  1. Install the cushion frame with the 4 bolts.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Attach the wire harness cramps.



    B213584
  1. w/ Seat Heater System:
    Attach the wire harness clamps.



8. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
  1. Set the seat heater to the seatback cover.



  1. Using a tacker, install the front seat heater to the seatback cover with the 6 tack pins as shown in the illustration.


    B122837E03

    NOTICE:
    Do not substitute other metal parts for tack pins.



9. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    B207459
  1. Install the seatback pad.



10. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B207626E01
  1. Using hog ring pliers, attach the strap of the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B207457
  1. Attach the 4 claws to install the 2 headrest supports.



    B207582E01
  1. Using hog ring pliers, install the upper part of the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B131236
  1. Attach the front seatback cover bracket and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B257947E01
  1. Using hog ring pliers, install the center of the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B209095E01
  1. Using hog ring pliers, attach the strap of the seatback cover to the seatback spring with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B207798E01
  1. Using hog ring pliers, attach the wires at the bottom of the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



11. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)


    B122839E03
  1. Set the front seat cushion heater to the seat cushion cover.

  1. Using a tacker, install the front seat cushion heater to the seat cushion cover with the 12 tack pins as shown in the illustration. A

    NOTICE:
    Do not substitute other metal parts for tack pins.



12. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B207627E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



13. INSTALL FRONT SEAT CUSHION PROTECTOR


    B207792
  1. Install the 2 protectors.



14. INSTALL SEAT CUSHION COVER WITH PAD


    B207795E03
  1. Set the seat cushion cover with pad in place.

  1. Using hog ring pliers, install the seat cushion cover with pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Attach the hooks in the hook area shown in the illustration.

  1. Attach the 2 hooks.

  1. Attach the wire harness clamps.



15. INSTALL SEATBACK SPRING
  1. Install the seatback spring.



16. INSTALL VERTICAL SEAT ADJUSTER KNOB RH (for RHD, w/ Vertical Adjuster)


    B108463
  1. Install the knob with the snap ring.



17. INSTALL FRONT SEAT CUSHION INNER SHIELD LH


    B108451E02
  1. Attach the rear part of the inner shield in the order shown in the illustration to install the cushion shield.

  1. Install the 2 screws.



18. INSTALL FRONT SEAT CUSHION COVER LH
  1. Install the seat cushion cover.



19. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)


B113103E01
  1. Install the buckle cover on the seat belt.



    B087821E01
  1. Install the seat belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.



    B087811E01
  1. w/ Driver seat belt warning light:
    Install the clamp as shown in the illustration.



20. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)


B113101E01
  1. Install the buckle cover on the inner belt.



    B084928E01
  1. Install the seat belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.



21. INSTALL FRONT SEAT CUSHION SHIELD LH


    B211022E02
  1. Attach the claw, and then attach the rear part of the cushion shield in the order shown in the illustration to install the cushion shield.

  1. Install the 2 screws.



22. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    B108464
  1. Install the release handle.