FRONT SEAT ASSEMBLY (for Separate Seat Type) > REASSEMBLY |
| 1. INSTALL SEAT TRACK COVER SPRING (for Walk in Seat Type) |
![]() |
Install the spring to the front seat outer track.
| 2. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR |
Install the seat cushion edge protector.
| 3. INSTALL RECLINING ADJUSTER ARM SUB-ASSEMBLY LOWER LH |
![]() |
w/ Vertical Adjuster:
Using a T40 "TORX" socket wrench, install the reclining adjuster arm with the 2 "TORX" bolts.
![]() |
w/o Vertical Adjuster:
Install the reclining adjuster arm with the 3 bolts.
| 4. INSTALL RECLINING ADJUSTER ARM SUB-ASSEMBLY LOWER RH |
w/ Vertical Adjuster:
Use the same procedures described for the LH side.
w/o Vertical Adjuster:
Use the same procedures described for the LH side.
| 5. INSTALL FRONT SEAT ADJUSTER ROD (w/ Vertical Adjuster) |
![]() |
Install the adjuster rod with the 2 bolts.
| 6. INSTALL SEAT TRACK ADJUSTING HANDLE |
![]() |
Attach the spring of the seat track in the order shown in the illustration to install the handle.
| 7. INSTALL VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (w/ Vertical Adjuster) |
![]() |
Install the vertical adjusting shaft to the reclining adjuster lower arm with 2 new E-rings.
![]() |
Temporarily install the vertical seat adjuster knob.
Turn the knob as much as possible in the direction indicated by arrow A in the illustration.
Mesh the gear of the vertical adjusting shaft with the gear of the reclining adjuster lower arm.
Align the holes of the adjusting shaft and adjusting arm by turning the knob in the direction indicated by arrow B in the illustration.
Remove the vertical seat adjuster knob.
![]() |
Install the seat spring as shown in the illustration.
Using pliers, push together the tabs that hold the spring.
Using a 6 mm socket hexagon wrench, install the front seat No. 2 adjuster pin.
| 8. INSTALL FRONT SEAT CUSHION PROTECTOR |
![]() |
Install the 2 protectors.
| 9. INSTALL FRONT SEAT CUSHION FRAME SUB-ASSEMBLY |
![]() |
Install the cushion frame with the 4 bolts.
![]() |
w/ Seat Heater system:
Install the cushion frame with the 4 bolts.
Attach the wire harness clamps.
| 10. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) |
![]() |
Set the front seat cushion heater to the seat cushion cover.
Using a tacker, install the front seat cushion heater to the seat cushion cover with the 12 tack pins as shown in the illustration.
| 11. INSTALL FRONT SEAT CUSHION COVER |
![]() |
for Normal Seat:
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
![]() |
for Leather:
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
![]() |
Set the seat cushion cover with pad in place.
Using hog ring pliers, install the seat cushion cover with pad with new hog rings.
Attach the hooks in the hook area shown in the illustration.
Attach the 2 hooks.
w/ Occupant Detection Sensor, w/ Seat Heater System:
Attach the wire harness clamps.
| 12. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) |
Set the seat heater to the seatback cover.
Using a tacker, install the front seat heater to the seatback cover with the 6 tack pins as shown in the illustration.

| 13. INSTALL FRONT SEATBACK PAD |
![]() |
Install the seatback pad.
| 14. INSTALL FRONT SEATBACK COVER |
![]() |
Using hog ring pliers, attach the 2 straps of the seatback cover to the seatback pad with new hog rings.
![]() |
Attach the 4 claws to install the 2 headrest supports.
![]() |
Using hog ring pliers, install the upper part of the seatback cover to the seatback pad with new hog rings.
![]() |
for Normal Seat:
Using hog ring pliers, install the center of the seatback cover to the seatback pad with new hog rings.
![]() |
for Leather Seat:
Using hog ring pliers, install the center of the seatback cover to the seatback pad with new hog rings.
![]() |
Using hog ring pliers, attach the 2 straps of the seatback cover to the seatback spring with new hog rings.
![]() |
Using hog ring pliers, attach the wires at the bottom of the seatback cover with new hog rings.
| 15. INSTALL FRONT SEATBACK ASSEMBLY |
![]() |
Install the seatback with the 4 bolts.
w/ Seat Heater System:
Connect the seatback heater connector.
| 16. INSTALL ADJUSTER TUBE (for Walk in Seat Type) |
Install the adjuster tube to the seatback spring.
| 17. INSTALL SEATBACK SPRING |
Install the seatback spring.
| 18. INSTALL SEAT TRACK CONTROL CABLE BRACKET LH (for Walk in Seat Type) |
![]() |
Install the bracket with a new E-ring.
| 19. INSTALL SEAT TRACK CONTROL CABLE BRACKET RH (for Walk in Seat Type) |
| 20. INSTALL FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH (for Walk in Seat Type) |
Install the fold seat lock control cable.
| 21. INSTALL FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH (for Walk in Seat Type) |
| 22. INSTALL FRONT SEAT CUSHION SHIELD INNER LH |
![]() |
Attach the rear part of the inner shield in the order shown in the illustration to install the cushion shield.
Install the 2 screws.
| 23. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) |
![]() |
Install the buckle cover on the seat belt.
![]() |
Install the seat belt with the nut.
![]() |
w/ Driver seat belt warning light:
Install the clamp as shown in the illustration.
| 24. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) |
![]() |
Install the buckle cover on the inner belt.
![]() |
Install the seat belt with the nut.
| 25. INSTALL FRONT SEAT CUSHION SHIELD LH |
![]() |
Attach the claw, and then attach the rear part of the cushion shield in the order shown in the illustration to install the cushion shield.
Install the 2 screws.
| 26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Install the release handle.
| 27. INSTALL VERTICAL SEAT ADJUSTER KNOB LH |
![]() |
Install the knob with the snap ring.