Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Bench Seat Type)

FRONT SEAT ASSEMBLY (for Bench Seat Type) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.



1. INSTALL FRONT SEAT CUSHION COVER (for TSAM Made)


  1. If installing a new front seat cushion pad:



      B112780E02
    1. Using hog ring pliers, install the front seat cushion cover to a new seat cushion pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

    2. Set the seat cushion cover with pad in place.



    3. B207675E01
    4. Using hog ring pliers, install the seat cushion cover with pad to the front seat cushion frame with new hog rings.



  1. If installing the front seat cushion pad with front seat cushion frame:



      B112780E02
    1. Using hog ring pliers, install the front seat cushion cover to the front seat cushion pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.



    2. B207675E01
    3. Using hog ring pliers, install the seat cushion cover with pad to the front seat cushion frame with new hog rings.

  1. w/ Occupant detection sensor:
    Attach the wire harness clamp.



2. INSTALL FRONT SEAT CUSHION COVER (for TMT Made)


  1. If installing a new front seat cushion pad:



      B112780E02
    1. Using hog ring pliers, install the front seat cushion cover to a new seat cushion pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

    2. Set the seat cushion cover with pad in place.



    3. B257813E01
    4. Using hog ring pliers, install the seat cushion cover with pad to the front seat cushion frame with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

    5. Attach the hooks.



  1. If installing the front seat cushion pad with front seat cushion frame:



      B112780E02
    1. Using hog ring pliers, install the front seat cushion cover to the front seat cushion pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.



    2. B257813E01
    3. Using hog ring pliers, install the front seat cushion cover to the front seat cushion frame with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

    4. Attach the hooks.

  1. w/ Occupant detection sensor:
    Attach the wire harness clamp.



3. INSTALL FRONT SEATBACK COVER


    B207674E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



4. INSTALL SEATBACK COVER WITH PAD


    B207679
  1. Set the seatback cover with pad in place and attach the 4 claws to install the 2 headrest supports.



    B207676E02
  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Attach the 2 pieces of fastening tape.



5. INSTALL FRONT SEATBACK ASSEMBLY


    B112300
  1. Install the seatback with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. INSTALL FRONT SEAT CUSHION SHIELD INNER RH


    B112769
  1. Attach the 2 claws and install the cushion shield.

  1. Install the screw.



7. INSTALL FRONT SEAT CUSHION SHIELD RH

HINT:
Use the same procedures described for the cushion shield inner RH.



8. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    B112297
  1. Install the release handle with the screw.