Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the intelligent tester ON.



  6. A114781E02
  7. Enter the following menus: Powertrain / Engine and ECT / Data List.

    HINT:
    To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.

  8. Read the Data List on the tester's screen.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Injector (Port)
    Injection period of the No. 1 cylinder/
    Min.: 0 ms, Max.: 32.64 ms
    Idling: 1 to 3 ms
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64°, Max.: 63.5°
    Idling: BTDC 0 to 20°
    -
    Calculate Load
    ECM calculated load/
    Min.: 0%, Max.: 100%
    1. Idling: 10 to 30%
    2. Running without load (2500 rpm): 10 to 40%
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from MAF meter/
    Min.: 0 g/s, Max.: 655.35 g/s
    1. Idling:
      1 to 4 g/sec.
    2. Running without load (2500 rpm):
      4 to 15 g/sec.
    If the value is approximately 0.0 g/sec.:
    1. Mass air flow meter power source circuit is open
    2. VG circuit is open or shorted
      If the value is 271.0 g/sec. or more:
    3. E2G circuit is open
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383.75 rpm
    Idling:
    600 to 700 rpm
    -
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    After warming up the engine:
    80 to 95°C (176 to 203°F)
    1. If the value is -40°C (-40°F): sensor circuit is open
    2. If the value is 140°C (284°F): sensor circuit is shorted
    Intake Air
    Intake air temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    Equivalent to ambient air temperature
    1. If the value is -40°C (-40°F): sensor circuit is open
    2. If the value is 140°C (284°F): sensor circuit is shorted
    2nd Air System Status
    Secondary air injection system status/ ON or OFF
    ON: Secondary air system operation
    -
    Air-Fuel Ratio
    Air-fuel ratio/
    Min.: 0, Max.: 1.998
    Idling: 0.8 to 1.2
    80 to 90°C (176 to 194°F) of coolant temperature
    Purge Density Lean Value
    Learning value of purge density/
    Min.: -50%, Max.: 349.99%
    Idling: -25 to 1%
    Service data
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 102.3%
    Idling: 0 to 6%
    -
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    The order signal from the ECM.
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -64° CA, Max.: 1983.9° CA
    0 to 18.5°CA
    Driving: 70 km/h (44 mph)
    Service data
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -64°CA, Max.: 1983.9°CA
    -10 to 0°CA
    Driving: 70 km/h (44 mph)
    Service data
    Accelerator Position No. 1
    Absolute accelerator pedal position No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: accelerator pedal is released
    54 to 86%: accelerator pedal is fully depressed
    -
    Accelerator Position No. 2
    Absolute accelerator pedal position No. 2/
    Min.: 0%, Max.: 100%
    12 to 42%: accelerator pedal is released
    66 to 98%: accelerator pedal is fully depressed
    -
    Accelerator Position No. 1
    Accelerator pedal position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. Accelerator pedal released:
      0.5 to 1.1 V
    2. Accelerator pedal depressed:
      2.6 to 4.5 V
    -
    Accelerator Position No. 2
    Accelerator pedal position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. Accelerator pedal released:
      1.2 to 2.0 V
    2. Accelerator pedal depressed:
      3.4 to 4.98 V
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor is detecting idle/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    Throttle Fully Close Learn
    Throttle fully closed
    (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 0.8 V
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No. 1 (AD)/
    Min.: 0 V, Max.: 4.9804 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1 /
    Min.: 0°, Max.: 124.5°
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2 /
    Min.: 0°, Max.: 124.5°
    -
    ETCS service data
    Fail Safe Drive
    Whether or not fail-safe function is executed/ ON or OFF
    ETCS has failed: ON
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail-safe function is executed/ ON or OFF
    ETCS has failed: ON
    -
    ST1
    Brake pedal/ ON or OFF
    Released: ON
    Depressed: OFF
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data
    Throttle Pos. Sensor Output
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. Throttle fully closed: 10 to 22%
    2. Throttle fully open: 66 to 98%
    Read the value with intrusive operation (active test)
    Throttle Idle Position
    Whether or not throttle position sensor is detecting idle/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 4.98 V
    Idling: 0.4 to 4.5 V
    (Inspection mode)
    -
    Throttle Sensor Position
    Throttle sensor positioning/
    Min.: 0%, Max.: 100%
    Idling 0 to 10%
    (Inspection mode)
    Calculated value based on VTA1
    Throttle Sensor Position #2
    Throttle sensor positioning #2/
    Min.: 0%, Max.: 100%
    -
    Calculated value based on VTA2
    Throttle Position No. 1
    Throttle position No. 1/
    Min.: 0 V, Max.: 4.98 V
    1. Throttle fully closed:
      0.5 to 1.2 V
    2. Throttle fully opened:
      3.2 to 4.8 V
    -
    Throttle Position No. 2
    Throttle position No. 2/
    Min.: 0 V, Max.: 4.98 V
    1. Throttle fully closed: 2.1 to 3.1 V
    2. Throttle fully open: 4.6 to 4.98 V
    Read the value with intrusive operation (Active Test)
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.9804 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/ Min.: 0, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/ Min.: 0, Max.: 4.9804 V
    2.2 to 2.6 V
    ETCS service data
    Throttle Sens Open #1 (AD)
    Throttle sensor opener position No. 1 (AD)/
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle motor control is permitted/ ON or OFF
    Idling: ON
    (Inspection mode)
    Read the value with the ignition switch ON (Do not start engine)
    Throttle Motor Current
    Throttle motor current/
    Min.: 0 A, Max.: 19.9 A
    Idling: 0 to 3.0 A
    -
    Throttle Motor DUTY
    Throttle motor/
    Min.: 0%, Max.: 100%
    Idling: 0.5 to 40%
    (Inspection mode)
    -
    Throttle Motor Duty (Open)
    Throttle motor duty ratio (open)/
    Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle motor duty ratio (close)/
    Min.: 0%, Max.: 100%
    -
    ETCS service data
    O2S B1 S2
    Heated oxygen sensor output voltage for bank 1 sensor 2/
    Min.: 0 V, Max.: 1.275 V
    Driving 70 km/h (44 mph): 0.1 to 0.9 V
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    AFS B1 S1
    A/F sensor output voltage for bank 1 sensor 1/
    Min.: 0 V, Max.: 7.999 V
    Idling: 2.8 to 3.8 V
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    Total FT #1
    Total fuel trim of bank 1
    Average value for fuel trim system of bank 1/
    Min.: -0.5, Max.: 0.496
    Idling: -0.2 to 0.2
    -
    Short FT #1
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
    Fuel System Status (Bank 1)
    Fuel system status (Bank 1) /
    Unused, OL, CL, OL Drive, OL Fault or CL Fault
    Idling after warming up: CL
    (Inspection mode)
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using heated oxygen sensor(s) as feedback for fuel control.
    3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    4. OL FAULT: Open loop due to detected system fault
    5. CL FAULT: Closed loop but heated oxygen sensor which is used for fuel control is malfunctioning
    Fuel System Status (Bank 2)
    Fuel system status (Bank 2) /
    Unused, OL, CL, OL Drive, OL Fault or CL Fault
    -
    -
    AF Lambda B1 S1
    Short-term fuel trim associated with bank 1 sensor 1/
    Min.: 0%, Max.: 1.99%
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air-fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS B1 S1
    Air fuel ratio sensor current bank 1 sensor 1/ Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of the sensor
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient temperature
    Service data
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient temperature
    Service data
    Injection Volume (Cylinder 1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.048 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times
    Starter Signal
    Starter signal/ ON or OFF
    ON: Cranking
    -
    Power Steering Switch
    Power steering signal/ ON or OFF
    ON: Power steering operation
    -
    Power Steering Signal
    Power steering signal/ ON or OFF
    ON: When steering wheel is first turned after ignition switch is turned to ON
    This signal status usually ON until ignition switch turned to OFF
    Closed Throttle Position SW
    Closed throttle position switch (idle switch)/ ON or OFF
    ON: Throttle valve is closed
    -
    A/C Signal
    A/C Signal/ ON or OFF
    ON: A/C switch is turned ON
    -
    Neutral Position SW Signal
    Park/Neutral position switch signal/
    ON or OFF
    P or N position: ON
    -
    Electrical Load Signal
    Electrical load signal/ ON or OFF
    ON: Headlights or defogger is turned ON
    -
    Stop Light Switch
    Stop light switch/ ON or OFF
    ON: Brake pedal is depressed
    -
    Immobiliser Communication
    Immobiliser communication/ ON or OFF
    ON: Normal
    -
    Fuel Cut Condition
    Fuel cut condition/ ON or OFF
    ON: Fuel cut operating
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power is input/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 19.9 V
    Idling: 10 to 15 V
    ETCS service data
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    Idling: 9 to 14 V
    (Inspection mode)
    -
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    Idling ON
    (Inspection mode)
    ETCS service data
    Atmosphere Pressure
    Atmosphere pressure/
    Min.: 0 kPa, Max.: 255 kPa
    -
    -
    Secondary Air Control VSV
    Secondary air injection system status/
    ON or OFF
    ON: Secondary air injection system operation
    -
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    Active Test support data
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    Active Test support data
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    VVT Control Status (Bank 1)
    VVT control status (Bank 1)/
    ON or OFF
    -
    Support for VVT Active Test
    TC and TE1
    TC and TE1 terminal of DLC3/
    ON or OFF
    -
    -
    AI Test
    Secondary air injection system operation prohibit/
    READY or NOT RDY
    -
    -
    Engine Speed of Cyl #1
    Engine rpm during No. 1 cylinder fuel cut/ Min.: 0 rpm, Max.: 25600 rpm
    -
    Active Test support data
    Engine Speed of Cyl #2
    Engine rpm during No. 2 cylinder fuel cut/ Min.: 0 rpm, Max.: 25600 rpm
    -
    Active Test support data
    Engine Speed of Cyl #3
    Engine rpm during No. 3 cylinder fuel cut/ Min.: 0 rpm, Max.: 25600 rpm
    -
    Active Test support data
    Engine Speed of Cyl #4
    Engine rpm during No. 4 cylinder fuel cut/ Min.: 0 rpm, Max.: 25600 rpm
    -
    Active Test support data
    Av Engine Speed of All Cyl
    Average of engine rpm values during fuel cut of No. 1 to No. 4 cylinders/ Min.: 0 rpm, Max.: 25600 rpm
    -
    Active Test support data
    VVT Aim Angle (Bank 1)
    VVT aim angle (Bank 1)/
    Min.: 0%, Max.: 100%
    Idling: 0%
    VVT duty signal value during forcible operation
    VVT Change Angle (Bank 1)
    VVT change angle/
    Min.: 0°FR, Max.: 60°FR
    Idling: 0 to 5°FR
    Displacement angle during forcible operation
    VVT OCV Duty (Bank 1)
    VVT OCV operation duty/
    Min.: 0%, Max.: 100%
    Idling: 0%
    Requested duty valve for forcible operation
    Idle Fuel Cut
    Fuel cut idle/ ON or OFF
    Fuel cut operation: ON
    Idle Fuel Cut = "ON" when throttle valve is fully closed and engine speed is over 2800 rpm
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/ ON or OFF
    Fuel cut operating: ON
    The fuel cut is being performed under very light load to prevent the engine combustion from becoming incomplete
    Ignition
    Ignition counter/
    Min.: 0, Max.: 800
    0 to 800
    -
    Cylinder #1 Misfire Count
    Misfire ratio of cylinder 1/
    Min.: 0, Max.: 255
    0
    This item is displayed only when idling
    Cylinder #2 Misfire Count
    Misfire ratio of cylinder 2/
    Min.: 0, Max.: 255
    0
    This item is displayed only when idling
    Cylinder #3 Misfire Count
    Misfire ratio of cylinder 3/
    Min.: 0, Max.: 255
    0
    This item is displayed only when idling
    Cylinder #4 Misfire Count
    Misfire ratio of cylinder 4/
    Min.: 0, Max.: 255
    0
    This item is displayed only when idling
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0 to 35
    -
    Misfire RPM
    Engine rpm for first misfire range/
    Min.: 0 rpm, Max.: 6,375 rpm
    Misfire 0: 0 rpm
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev., Max.: 3.98 g/rev.
    Misfire 0: 0 g/rev.
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -100%, Max.: 99.21%
    -100 to 99.22%
    Misfire detecting margin
    #Codes
    Number of codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTC
    Check Mode
    Check mode/ ON or OFF
    Check mode ON: ON
    -
    SPD Test
    Check mode result for vehicle speed sensor/
    0: Compl / 1: Incmpl
    -
    -
    OXS1 Test
    Check mode result for HO2 sensor/
    0: Compl / 1: Incmpl
    -
    -
    A/F Test Results (Bank 1)
    Check mode result for air-fuel ratio sensor/
    0: Compl / 1: Incmpl
    -
    -
    MIL
    MIL status/ ON or OFF
    MIL ON: ON
    -
    MIL ON Run Distance
    Distance traveled while MIL is activated/
    Min.: 0 km, Max.: 65,535 km
    Distance after DTC is detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 minutes, Max.: 65,535 minutes
    Equivalent to running time after MIL is turned on
    -
    Engine Run Time
    Engine run time/
    Min.: 0 seconds,
    Max.: 65,535 seconds
    Time after engine start
    Service data
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 minutes,
    Max.: 65,535 minutes
    Equivalent to time after DTC is cleared
    -
    Distance from DTC Cleared
    Distance from DTC cleared/
    Min.: 0 km, Max.: 65,535 km
    Equivalent to driven distance after DTC is cleared
    -
    Warmup Cycle Cleared DTC
    Warmup cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warmup cycles after DTC is cleared
    OBD Requirements
    OBD Requirements
    E-OBD
    -
    Number of Emission DTC
    Number of Emission DTCs
    -
    -
    Complete Parts Monitor
    Complete parts monitor/
    0: Not Avl / 1: Avail
    -
    -
    Model Code
    Model code
    -
    Identifying the model code:
    TGN###
    Engine Type
    Engine type
    -
    Identifying the engine type:
    2TRFE
    Cylinder Number
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying the cylinder number:
    4
    Transmission Type
    Transmission type
    -
    Identifying the transmission type:
    MT, ECT (4AT)
    Destination
    Destination
    -
    Identifying the destination:
    W
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying the model year:
    200#
    System Identification
    System identification
    -
    Identifying the engine system:
    Gasoline (gasoline engine)

    HINT:
    Normal Condition: If no conditions are specifically stated for "Idling", the shift lever is in P or N, the A/C switch is OFF and all accessory switches are OFF.


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the intelligent tester ON.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Control injection volume
    (Engine speed: 3000 rpm or less)
    Min.: -12.5%, Max.: 24.8%
    1. All injectors are tested at once
    2. Injection volume is gradually changed between -12.5% and 24.8%
    Control the Injection Volume for A/F Sensor
    Change injection volume
    Decreases by -12.5% or increases by 25%
    Following A/F Control procedure enables technician to check and graph output voltages of both A/F sensor and heated oxygen sensor.
    To display graph indication, select following menu items: View / Line graph 1 or Line graph 2.
    Activate the VSV for Secondary Air Control
    Activate the secondary air VSV
    ON or OFF
    This test activates VSV for only 5 seconds.
    After finishing this test, vehicle does not permit activating VSV again within 30 seconds.
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON or OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON or OFF
    -
    Control the Fuel Pump / Speed
    Control fuel pump
    ON or OFF
    Engine is stopped
    Connect the TC and TE1
    Connect TC and TE1
    ON or OFF
    -
    Control the Idle Fuel Cut Prohibit
    Control idle fuel cut prohibition
    ON or OFF
    During idling
    Control the ETCS Open/Close Slow Speed
    Control the ETCS opening/closing slow speed
    Open or Close
    Test possible when following conditions met:
    1. Ignition switch ON
    2. Engine is stopped
    3. Accelerator pedal is fully depressed
    Control the ETCS Open/Close Fast Speed
    Control the ETCS opening/closing fast speed
    Open or Close
    Test possible when following conditions met:
    1. Ignition switch ON
    2. Engine is stopped
    3. Accelerator pedal is fully depressed
    Control the VVT Linear (Bank 1)
    Control the VVT (Bank 1)
    Min.: -128%, Max.: 127%
    -
    Control the VVT System (Bank 1)
    Control VVT system (Bank 1)
    ON or OFF
    1. ON: Rough idle or engine stall
    2. OFF: Normal engine speed
    3. Vehicle is stopped
    4. Engine idling
    Control the Cylinder #1 Fuel Cut
    Control the cylinder #1 fuel cut
    ON or OFF
    Cylinder No. 1 fuel cut for power balance
    1. Vehicle is stopped
    2. Engine idling
    Control the Cylinder #2 Fuel Cut
    Control the cylinder #2 fuel cut
    ON or OFF
    Cylinder No. 2 fuel cut for power balance
    1. Vehicle is stopped
    2. Engine idling
    Control the Cylinder #3 Fuel Cut
    Control the cylinder #3 fuel cut
    ON or OFF
    Cylinder No. 3 fuel cut for power balance
    1. Vehicle is stopped
    2. Engine idling
    Control the Cylinder #4 Fuel Cut
    Control the cylinder #4 fuel cut
    ON or OFF
    Cylinder No. 4 fuel cut for power balance
    1. Vehicle is stopped
    2. Engine idling
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    Test possible while vehicle stopped and engine idling.
    Check the Cylinder Compression
    All cylinder injector fuel cut and ignition stop
    ON/OFF
    *

    HINT:
    *: When cranking the engine, the Active Test measures the speed of each cylinder.
    In this Active Test, the fuel of all cylinders is cut, and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is higher than the other cylinders, the compression pressure of that cylinder is determined to be lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the ignition switch ON and turn the intelligent tester ON.

    5. A173015
      Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the Compression menu, press the pull down menu button next to Primary. Then select Compression.

    6. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, the Active Test's Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine rpm measurement will enter standby.

    7. Fully open the throttle.
    8. Crank the engine for about 10 seconds.

    9. A173016
      Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the tester.

      HINT:
      At first, the tester's display will show each cylinder's engine rpm measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine rpm measurement will change to the actual engine rpm.

      NOTICE:
      1. When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.
      2. If the Check the Cylinder Compression test needs to be performed after it is turned ON and performed once, press Exit to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
      3. Use a fully-charged battery.