SFI SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
![]() |
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List on the tester's screen.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383.75 rpm | 650 to 750 rpm: Idle after engine warmed up | - |
| Calculate Load | ECM calculated load/ Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load/ Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from MAF meter/ Min.: 0 gm/s, Max.: 655.35 gm/s |
| If the value is approximately 0.0 gm/sec.:
|
| Coolant Temp | Engine coolant temperature/ Min.: -40°C (-40°F) Max.: 140°C (284°F) | After warming up the engine: 80 to 95°C (176 to 203°F) |
|
| Intake Air | Intake air temperature/ Min.: -40°C (-40°F) Max.: 140°C (284°F) | Equivalent to ambient air temperature |
|
| Engine Run Time | Engine run time/ Min.: 0 s Max.: 65535 s | Time after engine start | Service data |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C, Max.: 120°C | Close to ambient temperature | Service data |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C, Max.: 120°C | Close to ambient temperature | Service data |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | Idling: 9 to 14 V (Inspection mode) | - |
| Accel Sens. No.1 Volt % | Absolute accelerator pedal position No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal is released 54 to 86%: accelerator pedal is fully depressed | - |
| Accel Sens. No.2 Volt % | Absolute accelerator pedal position No. 2/ Min.: 0%, Max.: 100% | 12 to 42%: accelerator pedal is released 66 to 98%: accelerator pedal is fully depressed | - |
| Accel Sensor Out No.1 | Accelerator pedal position sensor No. 1 output voltage/ Min.: 0 V, Max.: 4.9 V | - | ETCS freeze data |
| Accel Sensor Out No.2 | Accelerator pedal position sensor No. 2 output voltage/ Min.: 0 V, Max.: 4.9 V | - | ETCS freeze data |
| Accel Sensor Out No.1 | Accelerator pedal position sensor No. 1 output voltage/ Min.: 0 V, Max.: 5 V |
| - |
| Accel Sensor Out No.2 | Accelerator pedal position sensor No. 2 output voltage/ Min.: 0 V, Max.: 5 V |
| - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Accel Fully Close #1 (AD) | Accelerator fully closed value No. 1 (AD)/ Min.: 0 V, Max.: 4.98 V | - | ETCS service data |
| Accel Fully Close Learn #1 | Accelerator fully closed learned value No. 1/ Min.: 0 deg, Max.: 124.5 deg | - | ETCS service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learned value No. 2/ Min.: 0 deg, Max.: 124.5 deg | - | ETCS service data |
| Throttle Sensor Volt % | Absolute throttle position sensor/ Min.: 0%, Max.: 100% |
| The calculated value based on VTA1 |
| Throttl Sensor #2 Volt % | Throttle sensor positioning #2/ Min.: 0%, Max.: 100% |
| The calculated value based on VTA2 |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed | - |
| System Guard | System guard/ ON or OFF | - | ETCS service data |
| Open Side Malfunction | Open side malfunction/ ON or OFF | - | ETCS service data |
| Throttle Idle Position | Whether or not throttle position sensor is detecting idle/ ON or OFF | Accelerator pedal released: ON Accelerator pedal depressed: OFF | - |
| Throttle Require Position | Throttle requirement position/ Min.: 0 V, Max.: 4.9 V | Idling: 0.5 to 1.1 V | - |
| Throttle Sensor Position* | Throttle sensor positioning/ Min.: 0%, Max.: 100% | Throttle fully closed: 0% Throttle fully open: 50 to 80% | Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 | Throttle position No. 1/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Throttle Position No. 2 | Throttle position No. 2/ Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| Throttle Position No. 1 | Throttle position No. 1/ Min.: 0 V, Max.: 5 V |
| - |
| Throttle Position No. 2 | Throttle position No. 2/ Min.: 0 V, Max.: 5 V |
| Read the value with intrusive operation (Active Test) |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.9 V | 0.5 to 4.8 V | ETCS service data |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1/ Min.: 0, Max.: 4.9 V | 0.6 to 1.4 V | ETCS service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2/ Min.: 0, Max.: 4.9 V | 1.7 to 2.5 V | ETCS service data |
| Throttle Sens Open #1 (AD) | Throttle sensor opener position No. 1 (AD)/ Min.: 0 V, Max.: 4.9 V | 0.5 to 4.8 V | - |
| Throttle Motor | Whether or not throttle motor control is permitted/ ON or OFF |
| - |
| Throttle Motor Current | Throttle motor current/ Min.: 0 A, Max.: 20 A | Idling: 0 to 3.0 A | - |
| Throttle Motor DUTY | Throttle motor/ Min.: 0%, Max.: 100% | Idling after engine warmed up: 10 to 22% | ETCS service data |
| Throttle Motor Current | Throttle motor current/ Min.: 0 A, Max.: 19.9 A | - | ETCS service data |
| Throttle Motor Open Duty | Throttle motor duty ratio/ Min.: 0%, Max.: 100% | - | ETCS service data |
| Throttle Motor Close Duty | Throttle motor duty ratio/ Min.: 0%, Max.: 100% | - | ETCS service data |
| Throttle Motor Duty (Open) | Throttle motor duty ratio (open)/ Min.: 0%, Max.: 100% | Idling: 0 to 40% | ETCS service data |
| Throttle Motor Duty (Close) | Throttle motor duty ratio (close)/ Min.: 0%, Max.: 100% | Idling: 0 to 40% | ETCS service data |
| Throttle Fully Close Learn | Throttle fully closed (learned value)/ Min.: 0 V, Max.: 4.98 V | Accelerator pedal released: 0.4 to 1.0 V | - |
| ETCS Actuator Power | Whether or not electric throttle control system power is input/ ON or OFF |
| - |
| +BM Voltage | +BM voltage/ Min.: 0 V, Max.: 19.9 V | Ignition switch ON and system normal: 11 to 14 V | ETCS service data |
| Actuator Power Supply | Actuator power supply/ ON or OFF | Idling ON (Inspection mode) | ETCS service data |
| Clutch Current | Clutch current/ Min.: 0 A, Max.: 2.49 A | - | ETCS service data |
| Electromagnetic Clutch | Electromagnetic clutch/ ON or OFF | - | - |
| Fail Safe Drive | Whether or not fail-safe function is executed/ ON or OFF |
| - |
| Fail Safe Drive (Main CPU) | Whether or not fail-safe function is executed/ ON or OFF |
| - |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 ms, Max.: 32.64 ms | 1.3 to 2.8 ms: Idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.047 ml | 0 to 0.5 ml | The total fuel injection volume of 10 injections. |
| Fuel Pump Speed Control | Fuel pump speed control status/ ON or OFF | Idling: ON | Active Test support data |
| Fuel Pump/Speed Status | Fuel pump/speed status/ ON or OFF | Idling: ON (Inspection mode) | - |
| EVAP (Purge) VSV | Purge VSV control duty/ Min.: 0%, Max.: 100% | 0 to 100%: During idling | The order signal from the ECM. |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 102.3% | 0 to 100%: During idling | - |
| Purge Density Learn Value | Learning value of purge density/ Min.: -50%, Max.: 349.99% | -40 to 0%: Idling | Service data |
| EVAP Purge VSV | VSV status for EVAP control/ ON or OFF | - | Active Test support data |
| Target Air-Fuel Ratio | Air-fuel ratio/ Min.: 0, Max.: 1.998 | Idling: 0.8 to 1.2 | - |
| AF Lambda B1S1 | Short-term fuel trim associated with bank 1 sensor 1/ Min.: 0%, Max.: 1.99 |
| - |
| AF Lambda B2S1 | Short-term fuel trim associated with bank 2 sensor 1/ Min.: 0%, Max.: 1.99 |
| - |
| AFS Voltage B1S1 | A/F sensor output voltage for bank 1 sensor 1/ Min.: 0 V, Max.: 7.99 V | Idling: 2.8 to 3.8 V | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor |
| AFS Voltage B2S1 | A/F sensor output voltage for bank 2 sensor 1/ Min.: 0 V, Max.: 7.99 V | Idling: 2.8 to 3.8 V | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor |
| AFS Current B1S1 | Air fuel ratio sensor current for bank 1 sensor 1/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor |
| AFS Current B2S1 | Air fuel ratio sensor current for bank 2 sensor 1/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor |
| O2S B1S2 | Heated oxygen sensor output voltage for bank 1 sensor 2/ Min.: 0 V, Max.: 1.27 V | Driving 70 km/h (44 mph): 0.1 to 0.9 V | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor |
| O2S B2S2 | Heated oxygen sensor output voltage for bank 2 sensor 2/ Min.: 0 V, Max.: 1.27 V | Driving 70 km/h (44 mph): 0.1 to 0.9 V | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor |
| Short FT #1 | Short-term fuel trim of bank 1/ Min.: -100%, Max.: 99.2% | -20 to 20% | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio |
| Long FT #1 | Long-term fuel trim of bank 1/ Min.: -100%, Max.: 99.2% | -20 to 20% | Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value |
| Total FT #1 | Total fuel trim of bank 1/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Short FT #2 | Short-term fuel trim of bank 2/ Min.: -100%, Max.: 99.2% | -20 to 20% | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio |
| Long FT #2 | Long-term fuel trim of bank 2/ Min.: -100%, Max.: 99.2% | -20 to 20% | Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value |
| Total FT #2 | Total fuel trim of bank 2/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (Bank 1)/ Unused, OL, CL, OL Drive, OL Fault or CL Fault | Idling after warming up: CL (Inspection mode) |
|
| Fuel System Status #2 | Fuel system status (Bank 2)/ Unused, OL, CL, OL Drive, OL Fault or CL Fault | Idling after warming up: CL (Inspection mode) |
|
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg, Max.: 63.5 deg | BTDC 7 to 24°: Idling (A/C OFF, shift position N) | - |
| Knock Feedback Value | Feedback value of knocking/ Min.: -64° CA, Max.: 1983.9° CA | -22 to 0 crankshaft angle: Driving, 70 km/h (44 mph) | Service data |
| Knock Correct Learn Value | Learned knocking correction value/ Min.: -64° CA, Max.: 1983.9° CA | 0 to 22 crankshaft angle: Driving, 70 km/h (44 mph) | Service data |
| ACIS VSV | VSV for ACIS/ ON or OFF | - | Active Test support data |
| VVT Control Status #1 | VVT control status (Bank 1)/ ON or OFF | - | Support for VVT Active Test |
| VVT Control Status #2 | VVT control status (Bank 2)/ ON or OFF | - | Support for VVT Active Test |
| VVT Aim Angle #1 | VVT aim angle (Bank 1)/ Min.: 0%, Max.: 100% | Idling: 0% | VVT duty signal value during forcible operation |
| VVT Change Angle #1 | VVT change angle (Bank 1)/ Min.: 0 DegFR, Max.: 60 DegFR | Idling: 0 to 5 DegFR | Displacement angle during forcible operation |
| VVT OCV Duty #1 | VVT OCV operation duty (Bank 1)/ Min.: 0%, Max.: 100% | Idling: 0% | Requested duty value for forcible operation |
| VVT Aim Angle #2 | VVT aim angle (Bank 2)/ Min.: 0%, Max.: 100% | Idling: 0% | VVT duty signal value during forcible operation |
| VVT Change Angle #2 | VVT change angle (Bank 2)/ Min.: 0 DegFR, Max.: 60 DegFR | Idling: 0 to 5 DegFR | Displacement angle during forcible operation |
| VVT OCV Duty #2 | VVT OCV operation duty (Bank 2)/ Min.: 0%, Max.: 100% | Idling: 0% | Requested duty value for forcible operation |
| Catalyst Temp B1S1 | Calculated catalyst temperature (bank 1 sensor 1)/ Min.: -40°C, Max.: 6513.5°C | 400 to 800°C: Catalyst is warmed up | - |
| Catalyst Temp B2S1 | Calculated catalyst temperature (bank 2 sensor 1)/ Min.: -40°C, Max.: 6513.5°C | 400 to 800°C: Catalyst is warmed up | - |
| Catalyst Temp B1S2 | Calculated catalyst temperature (bank 1 sensor 2)/ Min.: -40°C, Max.: 6513.5°C | 400 to 800°C: Catalyst is warmed up | - |
| Catalyst Temp B2S2 | Calculated catalyst temperature (bank 2 sensor 2)/ Min.: -40°C, Max.: 6513.5°C | 400 to 800°C: Catalyst is warmed up | - |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
| Power Steering Signal | Power steering signal/ ON or OFF | ON: Power steering operation | - |
| Power Steer. Sig. Record | Power steering signal (history)/ ON or OFF | ON: When steering wheel first turned after battery connected | Signal status usually ON until battery disconnected |
| Neutral Position SW Signal | PNP switch/ ON or OFF | ON: Shift position is P or N | For automatic transmission |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal is depressed | - |
| A/C Signal | A/C Signal/ ON or OFF | ON: A/C switch is turned ON | - |
| Closed Throttle Position SW | Closed throttle position switch (idle switch)/ ON or OFF | ON: Throttle valve is closed | - |
| Electrical Load Signal | Electrical load signal/ ON or OFF | ON: Headlights or defogger is turned ON | - |
| Check Mode | Check mode/ ON or OFF | Check mode ON: ON | - |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor/ Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for HO2 sensor/ Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for HO2 sensor/ Compl or Incmpl | - | - |
| A/F Test Result #2 | Check mode result for air-fuel ratio sensor/ Compl or Incmpl | - | - |
| A/F Test Result #1 | Check mode result for air-fuel ratio sensor/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Complete parts monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT Monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT Monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S(A/FS) Heater Monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S(A/FS) Heater Monitor/ Compl or Incmpl | - | - |
| O2S (A/FS) Monitor | O2S (A/FS) monitor/ Not Avl or Avail | - | - |
| O2S (A/FS) Monitor | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C Monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C Monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd Air Monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd Air Monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP Monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP Monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated Catalyst Monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated Catalyst Monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | MIL ON: ON | - |
| MIL ON Run Distance | Distance traveled while MIL is activated/ Min.: 0 km, Max.: 65,535 km | Distance after DTC is detected | - |
| Running Time from MIL ON | Running time from MIL ON/ Min.: 0 min, Max.: 65535 min | Equivalent to running time after MIL is turned on | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 min Max.: 65535 min | Equivalent to time after DTC is cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km, Max.: 65535 km | Equivalent to distance driven after DTC is cleared | - |
| Warmup Cycle Cleared DTC | Warmup cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warmup cycles after DTC is cleared |
| OBD Requirements | OBD Requirements | EOBD (Euro OBD) | - |
| Number of Emission DTC | Number of emission DTCs | - | - |
| TC and TE1 | TC and TE1 terminal of DLC3/ ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter/ Min.: 0, Max.: 65535 | 0 to 600 | - |
| Cylinder #1 Misfire Count | Misfire ratio of cylinder 1/ Min.: 0, Max.: 255 | 0 | - |
| Cylinder #2 Misfire Count | Misfire ratio of cylinder 2/ Min.: 0, Max.: 255 | 0 | - |
| Cylinder #3 Misfire Count | Misfire ratio of cylinder 3/ Min.: 0, Max.: 255 | 0 | - |
| Cylinder #4 Misfire Count | Misfire ratio of cylinder 4/ Min.: 0, Max.: 255 | 0 | - |
| Cylinder #5 Misfire Count | Misfire ratio of cylinder 5/ Min.: 0, Max.: 255 | 0 | - |
| Cylinder #6 Misfire Count | Misfire ratio of cylinder 6/ Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | Misfire count of all cylinders/ Min.: 0, Max.: 255 | 0 to 35 | - |
| Misfire RPM | Engine speed for first misfire range/ Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range/ Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring/ Min.: -128%, Max.: 127% | -100 to 99.22% | Misfire detecting margin |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | Active Test support data |
| Idle Fuel Cut | Fuel cut idle/ ON or OFF | Fuel cut operation: ON | Idle Fuel Cut = "ON" when throttle valve is fully closed and engine speed is over 2800 rpm |
| FC TAU | Fuel cut TAU: Fuel cut during very light load/ ON or OFF | Fuel cut operating: ON | The fuel cut is being performed under very light load to prevent the engine combustion from becoming incomplete |
| Model Code | Model code | - | Identifying the model code: GGN### |
| Engine Type | Engine type | - | Identifying the engine type: 1GRFE |
| Cylinder Number | Cylinder number/ Min.: 0, Max.: 255 | - | Identifying the cylinder number: 6 |
| Transmission Type | Transmission type | - | Identifying the transmission type: ECT 5th |
| Destination | Destination | - | Identifying the destination: W |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | Identifying the model year: 20## |
| System Identification | System identification | - | Identifying the engine system: Gasoline (gasoline engine) |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Control injection volume (Engine speed: 3000 rpm or less) | Min.: -12.5%, Max.: 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | Decreases by -12.5% or increases by 25% | Following A/F Control procedure enables technician to check and graph output voltages of both A/F sensor and heated oxygen sensor. To display graph indication, select following menu items: View / Line graph 1 or Line graph 2. |
| Activate the Fuel Pump Speed Control | Fuel pump speed control | ON (low speed)/OFF (high speed) | - |
| Activate the VSV for Intake Control | VSV for ACIS | ON or OFF | - |
| Activate the VSV for Evap Control | Activate purge VSV control | ON or OFF | - |
| Control the A/C Cut Signal | Control A/C cut signal | ON or OFF | - |
| Control the Fuel Pump / Speed | Control fuel pump | ON or OFF | Engine is stopped |
| Connect the TC and TE1 | Connect TC and TE1 | ON or OFF | - |
| Control the Idle Fuel Cut Prohibit | Control idle fuel cut prohibition | ON or OFF | During idling |
| Control the ETCS Open/Close Slow Speed | Control the ETCS opening/closing slow speed | Open or Close | Test possible when following conditions met:
|
| Control the ETCS Open/Close Fast Speed | Control the ETCS opening/closing fast speed | Open or Close | Test possible when following conditions met:
|
| Control the VVT Linear (Bank 1) | Control the VVT (Bank 1) | Min.: -128%, Max.: 127% | - |
| Control the VVT System (Bank 1) | Control VVT system (Bank 1) | ON or OFF |
|
| Control the VVT Linear (Bank 2) | Control the VVT (Bank 2) | Min.: -128%, Max.: 127% | - |
| Control the VVT System (Bank 2) | Control VVT system (Bank 2) | ON or OFF |
|
| Control the Cylinder #1 Fuel Cut | Control the cylinder #1 fuel cut | ON or OFF | Cylinder No. 1 fuel cut for power balance
|
| Control the Cylinder #2 Fuel Cut | Control the cylinder #2 fuel cut | ON or OFF | Cylinder No. 2 fuel cut for power balance
|
| Control the Cylinder #3 Fuel Cut | Control the cylinder #3 fuel cut | ON or OFF | Cylinder No. 3 fuel cut for power balance
|
| Control the Cylinder #4 Fuel Cut | Control the cylinder #4 fuel cut | ON or OFF | Cylinder No. 4 fuel cut for power balance
|
| Control the Cylinder #5 Fuel Cut | Control the cylinder #5 fuel cut | ON or OFF | Cylinder No. 5 fuel cut for power balance
|
| Control the Cylinder #6 Fuel Cut | Control the cylinder #6 fuel cut | ON or OFF | Cylinder No. 6 fuel cut for power balance
|
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling. |