DTC P0120/41 Throttle / Pedal Position Sensor / Switch "A" Circuit |
DTC P0122/41 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123/41 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220/41 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222/41 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223/41 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135/41 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| - | Conditions of DTC P0120/41, P0122/41, P0123/41, P0220/41, P0222/41 or P0223/41 continue for 2 seconds (open or short in throttle position sensor circuit) | - |
| P0120/41 | Output voltage of VTA1 quickly fluctuates up and down beyond upper and lower malfunction thresholds (1 trip detection logic) |
|
| P0122/41 | VTA1 is 0.2 V or less (1 trip detection logic) |
|
| P0123/41 | VTA1 is 4.535 V or more (1 trip detection logic) |
|
| P0220/41 | Output voltages of VTA1 and VTA2 quickly fluctuate beyond their respective upper and lower malfunction thresholds (1 trip detection logic) |
|
| P0222/41 | VTA2 is 1.75 V or less (1 trip detection logic) |
|
| P0223/41 | VTA2 is 4.8 V or more, VTA1 is between 0.2 V and 2.02 V (1 trip detection logic) |
|
| P2135/41 | Condition (a) continues for 0.5 seconds or more, or condition (b) continues for 0.4 seconds or more: (1 trip detection logic)
|
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position | 10 to 22% | 66 to 98% |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 4.98 V |

| 1.READ DATA LIST (THROTTLE POSITION, THROTTLE POSITION NO. 2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position and Throttle Position No. 2.
Read the values displayed on the intelligent tester.
| TP (VTA1) When AP Released | TP No. 2 (VTA2) When AP Released | TP (VTA1) When AP Depressed | TP No. 2 (VTA2) When AP Depressed | Suspected Area | Proceed to |
| 0% | 0 to 0.2 V | 0% | 0 to 0.2 V | VC circuit open | A |
| 100% | 4.5 to 4.98 V | 100% | 4.5 to 4.98 V | E2 circuit open | A |
| 0 or 100% | 2.1 to 3.1 V (Fail-safe) | 0% or 100% | 2.1 to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | A |
| 10 to 22% (Fail-safe) | 0 to 0.2 V or 4.5 to 4.98 V | 10 to 22% (Fail-safe) | 0 to 0.2 V or 4.5 to 4.98 V | VTA2 circuit open or ground short | A |
| 10 to 22% | 2.1 to 3.1 V | 66 to 98% (Not fail-safe) | 4.5 to 4.98 V (Not fail-safe) | Throttle position sensor circuit is normal | B |
|
| ||||
| A | |
| 2.CHECK WIRE HARNESS (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the T25 throttle body connector.
Disconnect the E12 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| T25-5 (VC) - E12-18 (VC) | Below 1 Ω |
| T25-6 (VTA1) - E12-20 (VTA1) T25-6 (VTA) - E12-20 (VTA1) | Below 1 Ω |
| T25-4 (VTA2) - E12-19 (VTA2) | Below 1 Ω |
| T25-3 (E2) - E12-28 (E2) | Below 1 Ω |
| T25-5 (VC) or E12-18 (VC) - Body ground | 10 kΩ or higher |
| T25-6 (VTA1) or E12-20 (VTA1) - Body ground T25-6 (VTA) or E12-20 (VTA1) - Body ground | 10 kΩ or higher |
| T25-4 (VTA2) or E12-19 (VTA2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK ECM (VC VOLTAGE) |
![]() |
Disconnect the T25 throttle body connector.
Turn the ignition switch ON and turn the intelligent tester ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E12-18 (VC) - E12-28 (E2) | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 5.CHECK IF DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Clear the DTCs (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
| One or more of P0120/41, P0122/41, P0123/41, P0220/41, P0222/41, P0223/41 and P2135/41 | A |
| No output | B |
|
| ||||
| A | ||
| ||
| 1.CHECK WIRE HARNESS (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the T25 throttle body connector.
Disconnect the E12 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| T25-5 (VC) - E12-18 (VC) | Below 1 Ω |
| T25-6 (VTA1) - E12-20 (VTA1) T25-6 (VTA) - E12-20 (VTA1) | Below 1 Ω |
| T25-4 (VTA2) - E12-19 (VTA2) | Below 1 Ω |
| T25-3 (E2) - E12-28 (E2) | Below 1 Ω |
| T25-5 (VC) or E12-18 (VC) - Body ground | 10 kΩ or higher |
| T25-6 (VTA1) or E12-20 (VTA1) - Body ground T25-6 (VTA) or E12-20 (VTA1) - Body ground | 10 kΩ or higher |
| T25-4 (VTA2) or E12-19 (VTA2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK ECM (VC VOLTAGE) |
![]() |
Disconnect the T25 throttle body connector.
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E12-18 (VC) - E12-28 (E2) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 3.REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 4.CHECK IF DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Clear the DTCs (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read DTC (Click here).
| Display (DTC Output) | Proceed to |
| One or more of P0120/41, P0122/41, P0123/41, P0220/41, P0222/41, P0223/41 and P2135/41 | A |
| No output | B |
|
| ||||
| A | ||
| ||