REAR PROPELLER SHAFT ASSEMBLY (for TSAM Made) > REASSEMBLY |
| 1. INSTALL CENTER NO. 1 SUPPORT BEARING ASSEMBLY |
![]() |
![]() |
Install the center support bearing to the intermediate shaft.
Coat the splines of the intermediate shaft with MP grease.
Install the washer.
Align the matchmarks on the center yoke and intermediate shaft.
Install the washer.
![]() |
Clamp the center yoke in a vise between aluminum plates and press the bearing into position by tightening a new nut.
Loosen the nut.
Torque the nut again.
![]() |
Using a chisel and hammer, stake the lock nut.
| 2. INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY |
![]() |
Apply MP grease to a new spider and bearings.
Fit the spider into the flange yoke.
![]() |
Using SST, install the 2 spider bearings to the spider.
![]() |
Using SST, adjust the spider bearings so that: 1) the flange yoke does not overlap the snap ring grooves of the spider bearings, and the grooves are as wide as possible; and 2) the groove width on both sides is the same.
Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness which will allow 0 to 0.05 mm (0 to 0.002 in.) axial play.
| Part No. | Thickness | Color |
| 90080-52174 | 1.38 mm (0.0543 in.) | Green |
| 90080-52044 | 1.384 mm (0.0545 in.) | Green |
| 90080-52043 | 1.435 mm (0.0565 in.) | Red |
| 90080-52175 | 1.45 mm (0.0571 in.) | Orange |
| 90080-52176 | 1.48 mm (0.0583 in.) | Black |
| 90080-52041 | 1.486 mm (0.0585 in.) | Black |
| 90080-52176 | 1.48 mm (0.0583 in.) | Black |
| 90080-52042 | 1.511 mm (0.0595 in.) | Copper |
| 90080-52040 | 1.537 mm (0.0605 in.) | Silver |
| 90080-52178 | 1.54 mm (0.0606 in.) | Yellow |
| 90080-52039 | 1.588 mm (0.0625 in.) | Yellow |
| 90080-52179 | 1.63 mm (0.0642 in.) | Red |
| 90080-52038 | 1.638 mm (0.0645 in.) | Blue |
| 90080-52180 | 1.68 mm (0.0661 in.) | Blue |
![]() |
Using a hammer, tap the flange yoke until there is no clearance between the spider bearings and snap rings.
Align the matchmarks on the yokes.
Align the matchmarks on the center yoke and the part it is connected to (yoke or shaft).
Install new spider bearings on the propeller shaft side.
| 3. INSTALL REAR SLIDING SHAFT BOOT (for 4WD) |
Temporarily install the boot (with 2 new clamps) to the propeller shaft.
Mount the propeller shaft in a soft vice.
Coat the splines of the propeller shaft with MP grease.
Align the matchmarks on the propeller shaft and sleeve yoke.
Install the sleeve yoke to the propeller shaft and connect the boot.
![]() |
Secure one of the boot clamps onto the boot.
Place SST onto the boot clamp.
Tighten SST so that the boot clamp is pinched as shown in the illustration.
![]() |
Using SST, adjust the clearance of the boot clamp.
For the remaining boot clamp, use the same procedures described above.
| 4. INSPECT REAR PROPELLER SHAFT ASSEMBLY (for 4WD) |
When replacing the spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

| 5. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY |
Check the spider bearings for wear or damage.
Check each spider bearing's axial play by turning the yoke while holding the shaft tightly.