REAR AXLE SHAFT > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE REAR WHEEL |
| 3. DRAIN BRAKE FLUID (for 2WD) |
| 4. DRAIN BRAKE FLUID (for 4WD and Pre-Runner) |
| 5. DISCONNECT BRAKE LINE (for 2WD) |
![]() |
Using SST, disconnect the brake line.
Remove the 2 bolts and cylinder.
| 6. DISCONNECT BRAKE LINE (for 4WD and Pre-Runner) |
![]() |
Using SST, disconnect the brake line.
Remove the 2 bolts and cylinder.
| 7. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for 2WD) |
Release the parking brake lever, and remove the drum.
![]() |
Remove the hole plug (adjust) and insert a screwdriver into the hole on the backing plate, and hold the automatic adjust lever away from the adjuster.
Using another screwdriver, compress the brake shoe adjuster by turning the adjusting wheel.
| 8. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for 4WD and Pre-Runner) |
Release the parking brake lever, and remove the drum.
![]() |
Remove the hole plug (adjust) and insert a screwdriver into the hole on the backing plate, and hold the automatic adjust lever away from the adjuster.
Using another screwdriver, compress the shoe adjuster by turning the adjusting wheel.
| 9. REMOVE REAR SPEED SENSOR LH (w/ ABS, VSC) |
Disconnect the sensor connector.

Detach the clamp.
Remove the 2 bolts and 2 harness clamps.
Remove the bolt and speed sensor LH.
Detach the 3 clamps.

Remove the bolt and harness clamp.
Remove the bolt and speed sensor RH.
| 10. REMOVE FRONT BRAKE SHOE (for 2WD) |
![]() |
Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.
Remove the shoe and tension spring.
| 11. REMOVE REAR BRAKE SHOE (for 2WD) |
![]() |
Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.
Using needle-nose pliers, remove the adjust lever tension spring from the automatic adjust lever. Then remove the shoe.
![]() |
Using needle-nose pliers, disconnect the No. 3 parking brake cable from the parking brake shoe lever.
| 12. REMOVE BRAKE SHOES (for 4WD and Pre-Runner) |
![]() |
Using pliers, remove the shoe hold down springs, pins, front brake shoe and rear brake shoe.
![]() |
Push the front or rear side of the wheel brake cylinder with the brake shoe. Then remove the side of the brake shoe opposite to the side of the cylinder being pushed. Finally remove the remaining side of the brake shoe.
![]() |
Move one of the shoes downward and remove the shoe tension spring.
![]() |
Remove the brake shoe front and rear side.
Remove the strut set and return spring from the shoe.
Remove the support clip from the strut set and return spring.
![]() |
Using needle-nose pliers, disconnect the No. 3 parking brake cable from the parking brake shoe lever.
| 13. DISCONNECT PARKING BRAKE CABLE |
Remove the 2 bolts and disconnect the parking brake cable.
| 14. REMOVE REAR AXLE SHAFT WITH BACKING PLATE |
![]() |
Remove the 4 nuts.
Pull out the axle shaft from the axle housing.
| 15. REMOVE O-RING |
Remove the O-ring from the axle housing.
| 16. REMOVE REAR AXLE SHAFT OIL SEAL LH |
![]() |
Using SST, tap out the oil seal.
| 17. REMOVE BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT |
![]() |
Temporarily install 4 nuts to the setting bolts.
Using a hammer, tap out the 4 setting bolts from the backing plate.
Remove the 4 nuts and 4 setting bolts.
| 18. REMOVE REAR AXLE BEARING INNER RETAINER LH AND REAR SKID CONTROL ROTOR (w/ ABS, VSC) |
![]() |
Grind the retainer and skid control rotor surfaces using a grinder, and then pry them off with a chisel and hammer.
| 19. REMOVE REAR AXLE BEARING INNER RETAINER LH |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Grind the retainer surface using a grinder, and then pry it off with a chisel and hammer.
Remove the shaft washer from the axle shaft.
| 20. REMOVE REAR AXLE SHAFT LH |
Insert the setting bolts into the backing plate and temporarily install washers and nuts to the setting bolts. Tighten the nuts to temporarily install the setting bolts to the backing plate and bearing case.
Remove the nuts and washers from the setting bolts.
![]() |
Install SST to the backing plate with the 4 nuts.
![]() |
Using SST and a press, press out the axle shaft.
Remove the 4 nuts and SST.
Temporarily install 4 nuts to the setting bolts.
Using a hammer, tap out the 4 setting bolts from the backing plate.
Remove the 4 nuts and 4 setting bolts.
| 21. REMOVE REAR AXLE HUB BOLT LH |
![]() |
Secure the axle shaft between aluminum plates in a vise.
for 2WD:
Using SST, remove the 5 hub bolts.
![]() |
for 4WD and Pre-Runner:
Using SST, remove the 6 hub bolts.
Remove the deflector and gasket from the axle shaft.
| 22. INSPECT REAR AXLE SHAFT LH |
![]() |
Using a dial indicator, measure the rear axle shaft shaft runout and flange runout.
| Item | Specified Condition |
| Shaft runout | 1.5 mm (0.0591 in.) |
| Flange runout | 0.10 mm (0.00394 in.) |
| 23. REMOVE REAR AXLE SHAFT OUTER OIL SEAL |
![]() |
Using SST, tap out the outer oil seal.
| 24. REMOVE REAR AXLE SHAFT BEARING LH |
![]() |
Using SST and a press, press out the bearing.