Home › BRAKE › BRAKE › BRAKE MASTER CYLINDER (for TSAM Made LHD wihtout ABS)

BRAKE MASTER CYLINDER (for TSAM Made LHD wihtout ABS) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    C122648E02
  1. Apply a light coat of lithium soap base glycol grease to the 2 new grommets and install them to the master cylinder.

  1. Install the reservoir with the screw.



2. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Install a new O-ring to the master cylinder.



    C122645
  1. Install the master cylinder and bracket (with 4-way) to the booster with the 2 nuts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



    C122644E01
  1. Using a union nut wrench, connect the 6 brake lines labeled C to the brake master cylinder and 4-way.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the brake fluid level warning switch connector labeled B to the master cylinder.

  1. for Manual Transmission:
    Connect the clutch reservoir tube labeled A to the master cylinder.



3. FILL RESERVOIR WITH BRAKE FLUID


C122637

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



4. BLEED AIR FROM BRAKE MASTER CYLINDER


C122638

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress and hold the brake pedal.



    C122639
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  

    Torque:
    15.2 N*m{ 155 kgf*cm , 11 ft.*lbf } without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



5. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for front brake
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for rear brake (2WD)
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake (4WD)

  1. Install the cap.



  1. Bleed air from the brake line for each wheel by repeating the above procedures.


    C111286E03



6. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)


C112661E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.



7. CHECK BRAKE FLUID LEVEL IN RESERVOIR


    F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



8. CHECK FOR BRAKE FLUID LEAKAGE