REAR DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT |
| 1. REMOVE REAR PROPELLER SHAFT ASSEMBLY |
Remove propeller shaft (Click here).
| 2. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange in place, remove the nut.
| 3. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, remove the companion flange.
| 4. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the oil seal.
| 5. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 6. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (inner).
![]() |
Using SST, tap out the roller bearing (outer).
| 7. REMOVE DIFFERENTIAL OIL STORAGE RING |
Using a screwdriver and hammer, tap out the oil storage ring.
| 8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
| 9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() |
Install a new bearing spacer.
| 10. INSTALL DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
| 11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a hammer, tap in a new roller bearing (outer).
Install the roller bearing (inner).
| 12. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 13. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
for TMC Made:
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal.
for DANA Made:
Apply MP grease to the lip of a new oil seal.
Using a brass bar and hammer, tap in a new oil seal until its surface is flush with the differential carrier end.
| 14. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, install the companion flange.
![]() |
Using SST to hold the companion flange in place, install the nut.
| 15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload.
| Item | Specified Condition |
| New bearing | 1.05 to 1.64 N*m (11 to 17 kgf*cm, 9.3 to 15 in.*lbf) |
| Reused bearing | 0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf) |
| 16. STAKE DRIVE PINION NUT |
![]() |
Using a chisel and hammer, stake the nut.
| 17. INSTALL REAR PROPELLER SHAFT ASSEMBLY |
Install propeller shaft (Click here).
| 18. REFILL DIFFERENTIAL OIL |
![]() |
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.
| Item | Temperature | Viscosity |
| Front differential (w/ A.D.D.) | SAE 75W-90 | |
| Front differential (w/o A.D.D.) Rear differential | Above -18°C (0°F) | SAE 90 |
| Below -18°C (0°F) | SAE 85W-90 | |
| Item | Oil type |
| Front differential Rear differential | Hypoid gear oil API GL-5 or equivalent |
| Rear differential (for LSD) | Hypoid gear oil LSD API GL-5 or equivalent |
| Item | Capacity |
| w/o A.D.D. | 1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.) |
| w/ A.D.D. | 1.60 to 1.70 liters (1.69 to 1.80 US qts., 1.40 to 1.50 Imp. qts.) |
| Item | Capacity |
| 2WD | 3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.) |
| 4WD | 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.) |
Check for oil leakage when the oil level is low.
Install the differential filler plug with a new gasket.
| 19. CHECK FOR DIFFERENTIAL OIL LEAKAGE |
![]() |
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.
| Item | Temperature | Viscosity |
| Front differential (w/ A.D.D.) | SAE 75W-90 | |
| Front differential (w/o A.D.D.) Rear differential | Above -18°C (0°F) | SAE 90 |
| Below -18°C (0°F) | SAE 85W-90 | |
| Item | Oil type |
| Front differential Rear differential | Hypoid gear oil API GL-5 or equivalent |
| Rear differential (for LSD) | Hypoid gear oil LSD API GL-5 or equivalent |
| Item | Capacity |
| w/o A.D.D. | 1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.) |
| w/ A.D.D. | 1.60 to 1.70 liters (1.69 to 1.80 US qts., 1.40 to 1.50 Imp. qts.) |
| Item | Capacity |
| 2WD | 3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.) |
| 4WD | 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.) |
Check for oil leakage when the oil level is low.
Install the differential filler plug with a new gasket.