FRONT DIFFERENTIAL CARRIER ASSEMBLY > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT WHEEL |
| 3. REMOVE FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE |
| 4. REMOVE NO. 1 ENGINE UNDER COVER |
| 5. REMOVE NO. 2 ENGINE UNDER COVER |
| 6. DRAIN DIFFERENTIAL OIL |
![]() |
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.
| Item | Temperature | Viscosity |
| Front differential (w/ A.D.D.) | SAE 75W-90 | |
| Front differential (w/o A.D.D.) Rear differential | Above -18°C (0°F) | SAE 90 |
| Below -18°C (0°F) | SAE 85W-90 | |
| Item | Oil type |
| Front differential Rear differential | Hypoid gear oil API GL-5 or equivalent |
| Rear differential (for LSD) | Hypoid gear oil LSD API GL-5 or equivalent |
| Item | Capacity |
| w/o A.D.D. | 1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.) |
| w/ A.D.D. | 1.60 to 1.70 liters (1.69 to 1.80 US qts., 1.40 to 1.50 Imp. qts.) |
| Item | Capacity |
| 2WD | 3.15 to 3.25 liters (3.30 to 3.43 US qts., 2.77 to 2.86 Imp. qts.) |
| 4WD | 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.) |
Check for oil leakage when the oil level is low.
Install the differential filler plug with a new gasket.
| 7. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
Remove propeller shaft (Click here).
| 8. REMOVE FRONT STABILIZER LINK ASSEMBLY LH |
Remove stabilizer link (Click here).
| 9. REMOVE FRONT STABILIZER LINK ASSEMBLY RH |
Remove stabilizer link (Click here).
| 10. REMOVE TIE ROD END SUB-ASSEMBLY LH |
| 11. REMOVE TIE ROD END SUB-ASSEMBLY RH |
| 12. REMOVE NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH |
Remove the suspension arm lower for 2WD (Click here).
Remove the suspension arm lower for 4WD and Pre-runner (Click here).
| 13. REMOVE NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER RH |
Remove the suspension arm lower for 2WD (Click here).
Remove the suspension arm lower for 4WD and Pre-runner (Click here).
| 14. DISCONNECT FRONT AXLE ASSEMBLY LH |
Disconnect the front axle for 2WD (Click here).
Disconnect the front axle for 4WD and Pre-runner (Click here).
| 15. DISCONNECT FRONT AXLE ASSEMBLY RH |
Disconnect the front axle for 2WD (Click here).
Disconnect the front axle for 4WD and Pre-runner (Click here).
| 16. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
Remove drive shaft (Click here).
| 17. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
Remove drive shaft (Click here).
| 18. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY |
![]() |
Remove the bolt and disconnect the differential breather tube bracket.
Support the differential with a jack.
Remove the No. 1 differential mounting nut.
Remove the 2 mounting bolts and 2 nuts.
Lower the jack and remove the front differential.
![]() |
Remove the 3 bolts and front No. 1 differential support.
![]() |
Remove the 2 bolts and front No. 2 differential support.
![]() |
Remove the 2 bolts and front No. 3 differential support.