Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.



2. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B087844E01
  1. Detach the 4 claws and remove the hole cover.



3. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


B115418E02

NOTICE:
Be careful not to damage the instrument panel lower and console box with the claws of the console panel upper.

  1. Detach the 12 claws and remove the console panel.



4. REMOVE CONSOLE BOX ASSEMBLY


B090153E01
  1. Remove the 4 screws <F> and 2 bolts <E>.

  1. Using a clip remover, remove the 2 clips and console box.



5. REMOVE SHIFT LEVER BOOT ASSEMBLY
  1. Remove the 4 screws and shift lever boot.



6. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E01
  1. Remove the 4 bolts and transfer high and low shift lever.

  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.

    HINT:
    Move the transfer shift lever to the H4 position.



7. REMOVE NO. 1 ENGINE UNDER COVER


8. REMOVE NO. 2 ENGINE UNDER COVER


9. REMOVE FRONT EXHAUST PIPE ASSEMBLY


A169038
  1. Disconnect the heated oxygen sensor connector.

  1. Detach the 3 wire clamps.

  1. Remove the 2 bolts and 2 nuts, disconnect the front pipe from the center pipe and remove the gasket.

  1. Remove the 2 bolts and 2 compression springs, disconnect the front pipe from the exhaust manifold and remove the gasket.

  1. Remove the front pipe from the pipe support.



10. REMOVE TRANSFER CASE LOWER PROTECTOR
  1. Remove the 4 bolts and transfer case lower protector.



11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. Remove the front propeller shaft assembly (Click here).



12. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Remove the propeller with center bearing shaft assembly (Click here).



13. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



14. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


C118024
  1. Remove the oil dipstick.

  1. Remove the 2 bolts and oil filler tube.

  1. Remove the O-ring from the oil filler tube.



15. DISCONNECT OIL COOLER TUBE


C118031
  1. Using a union nut wrench, disconnect the tube outlet and tube inlet.



    C118032
  1. Remove the 3 bolts and 3 clamps.



16. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.



17. REMOVE TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Remove the 2 bolts and control cable bracket from the transmission.



18. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and seal.



19. REMOVE STARTER ASSEMBLY


    G039103E03
  1. Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.

  1. Remove the 2 bolts and starter.



20. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


G034518E01
  1. Support the transmission with a transmission jack.



21. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256E01
  1. *1: Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. *2: Remove the 4 nuts, 4 bolts and frame crossmember.



22. DISCONNECT CONNECTOR


G034519E01
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Transmission side:
    Disconnect the connectors.

    1. Disconnect the temperature sensor connector.

    2. Disconnect the park/neutral position switch connector.

    3. Disconnect the 2 speed sensor connectors.

    4. Disconnect the transmission wire connector.

  1. Transfer side:
    Disconnect the connectors.

    1. Disconnect the indicator switch connector (for 4WD).

    2. Disconnect the speedometer sensor connector.

    3. Disconnect the indicator switch connector (for L4).

    4. Disconnect the indicator switch connector (neutral).



23. DISCONNECT WIRE HARNESS


24. REMOVE FLYWHEEL HOUSING DUST SEAL


25. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


C118033
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch mounting bolts.



    C118034
  1. Remove the 3 bolts and exhaust manifold stay.



    C118035
  1. Remove the 7 bolts.

  1. Separate the transmission from the engine.



26. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR


G034260E01
  1. Remove the 4 bolts and engine mounting insulator.



27. REMOVE TRANSFER ASSEMBLY
Remove the transfer assembly (Click here).


28. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY