Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY

NOTICE:
  1. Before installing the seal packing, remove ignition source from the vicinity.
  2. Do not allow seal packing to contact any unnecessary areas.
  3. When installing the seal packing, wear appropriate protective equipment.
  4. When storing seal packing, keep it away from direct sunlight and high temperature areas.
  5. After applying seal packing to the axle housing and gasket, wait 1 to 4 minutes before installing them to the differential carrier.

  1. Clean the contact surfaces of the differential carrier and axle housing.

    NOTICE:
    Be careful not to damage the installation surface.

  1. Apply seal packing to the rear axle housing.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Apply seal packing to the differential carrier.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Install the differential carrier and a new gasket with the 10 nuts and washers.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    1. Be careful to install the gasket without tearing it.
    2. After drying of the seal packing (after approximately 90 minutes), retighten the 10 nuts to specified torque.



2. INSTALL REAR DIFFERENTIAL LOCK ACTUATOR BREATHER TUBE


3. INSTALL REAR AXLE SHAFT LH OIL SEAL
  1. Install the axle shaft oil seal (Click here).



4. INSTALL REAR AXLE SHAFT RH OIL SEAL
  1. Install the axle shaft oil seal (Click here).



5. INSTALL REAR AXLE SHAFT WITH BACKING PLATE LH
  1. Install the axle shaft with backing plate (Click here).



6. INSTALL REAR AXLE SHAFT WITH BACKING PLATE RH
  1. Install the axle shaft with backing plate (Click here).



7. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the parking brake cable for 2WD (Click here).

  1. Install the parking brake cable for 4WD and Pre-runner (Click here).



8. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY


9. INSTALL REAR SPEED SENSOR LH
  1. Install the speed sensor .



10. INSTALL REAR SPEED SENSOR RH
  1. Install the speed sensor .



11. INSTALL PARKING BRAKE SHOE LH
  1. Install the parking brake shoe (Click here).



12. INSTALL PARKING BRAKE SHOE RH
  1. Install the parking brake shoe (Click here).



13. INSTALL BRAKE PEDAL RETURN SPRING LH
  1. Install the return spring for 2WD (Click here).

  1. Install the return spring for 4WD and Pre-runner (Click here).



14. INSTALL BRAKE PEDAL RETURN SPRING RH
  1. Install the return spring for 2WD (Click here).

  1. Install the return spring for 4WD and Pre-runner (Click here).



15. CHECK PARKING BRAKE INSTALLATION
  1. Check the installation of the parking brake (Click here).



16. BLEED AIR FROM BRAKE LINE
  1. Bleed the air from brake line (Click here).



17. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level in the reservoir (Click here).



18. CHECK FOR BRAKE FLUID LEAKAGE
  1. Check for brake fluid leakage (Click here).



19. REFILL DIFFERENTIAL OIL
  1. Refill the differential oil (Click here).



20. CHECK FOR DIFFERENTIAL OIL LEAKAGE
  1. Inspect and adjust the differential oil (Click here).



21. INSTALL REAR PROPELLER SHAFT ASSEMBLY
Install the propeller shaft (Click here).


22. INSTALL REAR WHEEL


23. INSPECT PARKING BRAKE PEDAL TRAVEL
  1. Inspect the parking brake pedal travel (Click here).



24. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Adjust the parking brake pedal travel (Click here).



25. CHECK ABS SPEED SENSOR SIGNAL
  1. Check the ABS speed sensor signal (Click here).