Home › ENGINE ยท 5L-E › FUEL › FUEL INJECTION NOZZLE

FUEL INJECTION NOZZLE > INSTALLATION

for Preparation Click here



1. INSTALL NOZZLE HOLDER AND NOZZLE SET


    A122389E01
  1. Place 4 new injection nozzle seat gaskets and 4 injection nozzle seats into the injection nozzle holes of the cylinder head.

  1. Using SST, install the 4 nozzle holders and nozzle sets.

    SST
    09268-64010   (09268-64020)

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



2. INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY


    A121941
  1. Install 4 new ring packing washers and the leakage pipe with the 4 nuts.

    Torque:
    29.5 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. Connect the fuel hose to the leakage pipe.



3. INSTALL NO. 1 GLOW PLUG CONNECTOR
  1. Remove the nut and wire harness.

  1. Remove the 4 screw grommets, 4 nuts and glow plug connector.



4. INSTALL INJECTION PIPE SET


    A122388E01
  1. Connect the 2 lower clamps on the intake manifold.

  1. Install the 4 injection pipes.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf } for use with SST
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf } for use without SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.)

  1. Secure the injection pipes with the 2 upper pipe clamps and 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



5. BLEED INJECTION PIPE
  1. Move the priming pump in the upper part of the fuel filter assembly up and down, and fill the injection pump assembly and fuel system with fuel.

  1. Loosen one of the union nuts (in the nozzle side).

  1. Crank the engine until fuel comes out from the union nut (in the nozzle side).

  1. Tighten the union nut.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf } for use with SST
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf } for use without SST

  1. Perform the procedures above for each injection pipe.



6. INSTALL VENTURI
  1. Place a new gasket and the venturi on the intake manifold.



    A111053E02
  1. Connect the throttle control motor connector.



    A111052E02
  1. Connect the throttle open switch connector.



7. INSTALL INTAKE PIPE ASSEMBLY


    A114290
  1. Connect the intake pipe to the intake flange with the clamp.

  1. Fix the intake pipe in place with the 2 bolts and clamp.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf } for bolt
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf } for clamp



8. CONNECT AIR CLEANER HOSE
  1. Connect the air cleaner hose to the air cleaner and intake pipe with the 2 clamps.

  1. Fix the intake pipe in place with the 2 clamps.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the IAT sensor connector.

  1. Attach the clamp of the IAT sensor harness.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


10. CHECK FOR FUEL LEAKS
  1. Check that there are no fuel leaks anywhere on the fuel system after performing maintenance.

    HINT:
    When checking for fuel leaks, make sure that there is pressure in fuel line.