Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Power Windows do not Operate at All

for Preparation Click here


DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch may have no power or may be malfunctioning.

WIRING DIAGRAM


B107970E09


B117122E08


INSPECTION PROCEDURE

1.INSPECT FUSE (ECU-IG & GAUGE, PWR, DOOR)
  1. Remove the ECU-IG & GAUGE fuse from the instrument panel junction block.

  1. Remove the PWR fuse from the No. 3 relay block.

  1. Remove the DOOR fuse from the No. 3 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.INSPECT RELAY (Marking: IG1)
B112776
  1. Remove the IG1 relay from the No. 3 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE RELAY
OK


3.INSPECT IGNITION SWITCH ASSEMBLY
A087913E01
  1. Remove the ignition switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 (IG1) - 4 (AM1)
    OFF
    10 kΩ or higher
    1 (IG1) - 4 (AM1)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


4.CHECK WIRE HARNESS (MASTER SWITCH - BATTERY AND BODY GROUND)


    B117126E43
  1. for Single cab, Extra cab

    1. Disconnect the P4 master switch connector.

    2. Measure the voltage of the wire harness side connectors.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-9 (B) - Body ground
      Ignition switch ON
      10 to 14 V
      P4-9 (B) - Body ground
      Ignition switch OFF
      Below 1 V

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      P4-10 (E) - Body ground*1
      Below 1 Ω
      P4-1 (E) - Body ground*2
      Below 1 Ω

      HINT:
      1. *1: for LHD
      2. *2: for RHD



    B117126E37
  1. for Double cab

    1. Disconnect the P4 master switch connector.

    2. Measure the voltage of the wire harness side connectors.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-6 (B) - Body ground
      Ignition switch ON
      10 to 14 V
      P4-6 (B) - Body ground
      Ignition switch OFF
      Below 1 V
      P4-7 (BW) - Body ground*2
      Always
      10 to 14 V

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      P4-1 (E) - Body ground*2
      Below 1 Ω
      P4-3 (E) - Body ground*1
      Below 1 Ω

      1. *1: w/o Jam protection
      2. *2: w/ Jam protection



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY