Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual UP / DOWN and AUTO DOWN functions do not operate, a malfunction may be present in the power window regulator master switch, power window regulator motor or wire harness.

WIRING DIAGRAM


B107967E14


B117121E10


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (VOLTAGE)


    B144132E02
  1. for Single cab, Extra cab

    1. Disconnect the P4 master switch connector.

    2. Measure the voltage of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-6 (B) - Body ground
      Ignition switch ON
      10 to 14 V
      P4-6 (B) - Body ground
      Ignition switch OFF
      Below 1 V



    B117126E35
  1. for Double cab

    1. Disconnect the P4 master switch connector.

    2. Measure the voltage of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      P4-7 (BW) - Body ground
      Always
      10 to 14 V
      P4-6 (B) - Body ground
      Ignition switch ON
      10 to 14 V
      P4-6 (B) - Body ground
      Ignition switch OFF
      Below 1 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)


    B086401E01
  1. for LHD:

    1. Remove the motor.

    2. Apply battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates counterclockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates clockwise



    B086400E01
  1. for RHD:

    1. Remove the motor.

    2. Apply battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates counterclockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)
OK


3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DRIVER SWITCH)


    B112772E11
  1. for LHD (for Single cab, Extra cab):

    1. Remove the master switch.

    2. Measure the voltage of the switch when the switch is operated.

      Standard voltage:

      Tester Connection
      Switch Condition
      Specified Condition
      3 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 10 to 14 V
      4 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 10 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 10 to 14 V → Below 1 V



    B085836E06
  1. for RHD (for Single cab, Extra cab):

    1. Remove the master switch.

    2. Measure the voltage of the switch when the switch is operated.

      Standard voltage:

      Tester Connection
      Switch Condition
      Specified Condition
      2 (U) - 10 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 10 to 14 V
      5 (D) - 10 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 10 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 10 to 14 V → Below 1 V



    B059314E35
  1. for LHD (for Double cab):

    1. Remove the master switch.

    2. Measure the voltage of the switch when the switch is operated.

      Standard voltage:

      Tester Connection
      Switch Condition
      Specified Condition
      4 (U) - 3 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 10 to 14 V
      9 (D) - 3 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 10 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 10 to 14 V → Below 1 V



    B085831E22
  1. for RHD (for Double cab):

    1. Remove the master switch.

    2. Measure the voltage of the switch when the switch is operated.

      Standard voltage:

      Tester Connection
      Switch Condition
      Specified Condition
      4 (U) - 3 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 10 to 14 V
      9 (D) - 3 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 10 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 10 to 14 V → Below 1 V



  1. w/ Jam protection


    B144123E02

    1. Remove the power window regulator master switch with its connectors still connected.

    2. Measure the voltage of the power window regulator master switch connector.

      Standard voltage:

      Tester Connection
      Switch Condition
      Specified Condition
      4 (U) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → UP (manual operation)
      Below 1 V → 10 to 14 V
      Ignition switch ON, driver side power window fully opened → driver side power window switch UP (AUTO operation) → driver side power window fully close
      Below 1 V → 10 to 14 V → Below 1 V
      9 (D) - 1 (E)
      Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
      Below 1 V → 10 to 14 V
      Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
      Below 1 V → 10 to 14 V → Below 1 V



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


4.CHECK WIRE HARNESS (MASTER SWITCH - MOTOR)

B111939E08

  1. for LHD:

    1. Disconnect the P4 master switch connector.

    2. Disconnect the P5 motor connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      for Single cab, Extra cab:
      Tester Connection
      Specified Condition
      P4-4 (D) - P5-1
      Below 1 Ω
      P4-3 (U) - P5-2
      Below 1 Ω
      P4-4 (D) or P5-1 - Body ground
      10 kΩ or higher
      P4-3 (U) or P5-2 - Body ground
      10 kΩ or higher

      Standard resistance:
      for Double cab:
      Tester Connection
      Specified Condition
      P4-9 (D) - P5-1
      Below 1 Ω
      P4-4 (U) - P5-2
      Below 1 Ω
      P4-9 (D) or P5-1 - Body ground
      10 kΩ or higher
      P4-4 (U) or P5-2 - Body ground
      10 kΩ or higher


B111939E09

  1. for RHD:

    1. Disconnect the P4 master switch connector.

    2. Disconnect the P6 motor connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      for Single cab, Extra cab:
      Tester Connection
      Specified Condition
      P4-5 (D) - P6-1
      Below 1 Ω
      P4-2 (U) - P6-2
      Below 1 Ω
      P4-5 (D) or P6-1 - Body ground
      10 kΩ or higher
      P4-2 (U) or P6-2 - Body ground
      10 kΩ or higher

      Standard resistance:
      for Double cab:
      Tester Connection
      Specified Condition
      P4-9 (D) - P6-1
      Below 1 Ω
      P4-4 (U) - P6-2
      Below 1 Ω
      P4-9 (D) or P6-1 - Body ground
      10 kΩ or higher
      P4-4 (U) or P6-2 - Body ground
      10 kΩ or higher



  1. w/ Jam protection


    B117125E28

    1. Disconnect the P4 master switch connector.

    2. Disconnect the P5*1 or P6*2 motor connector.

      HINT:
      *1: for LHD
      *2: for RHD

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      for LHD:
      Tester Connection
      Specified Condition
      P4-9 (D) - P5-1
      Below 1 Ω
      P4-4 (U) - P5-2
      Below 1 Ω
      P4-9 (D) or P5-1 - Body ground
      10 kΩ or higher
      P4-4 (U) or P5-2 - Body ground
      10 kΩ or higher

      Standard resistance:
      for RHD:
      Tester Connection
      Specified Condition
      P4-9 (D) - P6-1
      Below 1 Ω
      P4-4 (U) - P6-2
      Below 1 Ω
      P4-9 (D) or P6-1 - Body ground
      10 kΩ or higher
      P4-4 (U) or P6-2 - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY