POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch |

| 1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE) |
![]() |
Disconnect the P9 regulator switch connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| P9-3 - Body ground | Ignition switch ON | 10 to 14 V |
| P9-3 - Body ground | Ignition switch OFF | Below 1 V |
|
| ||||
| OK | |
| 2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) |
![]() |
Remove the switch.
Measure the resistance of the switch when the switch is operated.
| Tester Connection | Switch Condition | Specified Condition |
| 5 - 4 2 - 3 | UP | Below 1 Ω |
| 5 - 4 2 - 1 | OFF | Below 1 Ω |
| 5 - 3 2 - 1 | DOWN | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK WIRE HARNESS (FRONT PASSENGER SIDE SWITCH - FRONT PASSENGER SIDE MOTOR) |

Disconnect the P9 switch connector.
Disconnect the P6*1 or P5*2 motor connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| P9-5 - P6-1 | Below 1 Ω |
| P9-2 - P6-2 | Below 1 Ω |
| P9-5 or P6-1 - Body ground | 10 kΩ or higher |
| P9-2 or P6-2 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| P9-5 - P5-1 | Below 1 Ω |
| P9-2 - P5-2 | Below 1 Ω |
| P9-5 or P5-1 - Body ground | 10 kΩ or higher |
| P9-2 or P5-2 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FRONT PASSENGER SIDE POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
for LHD:
Remove the motor.
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates clockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates counterclockwise |
![]() |
for RHD:
Remove the motor.
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates counterclockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates clockwise |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (MASTER SWITCH - FRONT PASSENGER SIDE SWITCH) |
for LHD:

Disconnect the P4 master switch connector.
Disconnect the P9 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| P4-8 (U) - P9-1 | Below 1 Ω |
| P4-10 (D) - P9-4 | Below 1 Ω |
| P4-8 (U) or P9-1 - Body ground | 10 kΩ or higher |
| P4-10 (D) or P9-4 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| P4-18 (U) - P9-1 | Below 1 Ω |
| P4-15 (D) - P9-4 | Below 1 Ω |
| P4-18 (U) or P9-1 - Body ground | 10 kΩ or higher |
| P4-15 (D) or P9-4 - Body ground | 10 kΩ or higher |
for RHD:

Disconnect the P4 master switch connector.
Disconnect the P9 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| P4-8 (U) - P9-1 | Below 1 Ω |
| P4-1 (D) - P9-4 | Below 1 Ω |
| P4-8 (U) or P9-1 - Body ground | 10 kΩ or higher |
| P4-1 (D) or P9-4 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| P4-10 (U) - P9-1 | Below 1 Ω |
| P4-13 (D) - P9-4 | Below 1 Ω |
| P4-10 (U) or P9-1 - Body ground | 10 kΩ or higher |
| P4-13 (D) or P9-4 - Body ground | 10 kΩ or higher |
w/ Jam protection

Disconnect the P4 master switch connector.
Disconnect the P9 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| P4-13 (U) - P9-1 | Below 1 Ω |
| P4-15 (D) - P9-4 | Below 1 Ω |
| P4-13 (U) or P9-1 - Body ground | 10 kΩ or higher |
| P4-15 (D) or P9-4 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||