Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio and visual system cannot be operated using the steering pad switch.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the audio and visual system cannot be operated using the steering pad switch, and the audio and visual system itself cannot function.

WIRING DIAGRAM


E171402E04


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)


    E171409E03
  1. Disconnect the R12 receiver connector.

  1. Disconnect the S13 cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R12-8 (SW2) - S13-5 (AU2)
    Always
    Below 1 Ω
    R12-6 (SWG) - S13-4 (EAU)
    R12-7 (SW1) - S13-6 (AU1)
    R12-8 (SW2) - Body ground
    Always
    10 kΩ or higher
    R12-6 (SWG) - Body ground
    R12-7 (SW1) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SPIRAL CABLE
E171452E01
  1. Disconnect the cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S13-4 (EAU) - 8 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    S13-5 (AU2) - 9 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    S13-6 (AU1) - 10 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the supplemental restraint system (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY

E171665E02

  1. Disconnect the switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (AU2) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    MODE switch is pushed
    Below 2.5 Ω
    10 (AU1) - 8 (EAU)
    No switch is pushed
    100 kΩ or higher
    Seek+ switch is pushed
    Below 2.5 Ω
    Seek- switch is pushed
    329 Ω
    Vol+ switch is pushed
    1000 Ω
    Vol- switch is pushed
    3110 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (飛び先がまだ未登録)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)