Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Warning Buzzer does not Sound

for Preparation Click here


WIRING DIAGRAM


E117520E06


INSPECTION PROCEDURE

1.INSPECT FUSE (TAIL)
  1. Remove the TAIL fuse from the instrument panel junction block (driver side junction block).

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK COMBINATION METER BUZZER (OPERATION)
  1. Check the key reminder warning buzzer operation.

    1. Turn the ignition switch OFF with the key inserted into the ignition key cylinder.

    2. Open the driver side door.

      OK:
      Warning buzzer sounds.

  1. Check the light reminder warning buzzer operation.

    1. Turn the ignition switch OFF.

    2. Set the light control switch to the TAIL or HEAD position.

    3. Open the driver side door.

      OK:
      Warning buzzer sounds.

      Result:
      Result
      Proceed to
      Key reminder warning buzzer does not sound
      A
      Light reminder warning buzzer does not sound
      B



B
Go to step 5
A


3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
B085913E01
  1. Remove the unlock warning switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Pushed (ON)
    Below 1 Ω
    Not pushed (OFF)
    10 kΩ or higher



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


4.CHECK WIRE HARNESS (SWITCH - METER AND BODY GROUND)
E110282E10
  1. Disconnect the U1 switch connector.

  1. Disconnect the C8 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    U1-1 - C8-10
    Below 1 Ω
    U1-2 - Body ground



OK
Go to step 7
NG

REPAIR OR REPLACE HARNESS AND CONNECTOR 

5.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (LIGHT CONTROL SWITCH)
E110283E01
  1. Remove the headlight dimmer switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    13 (B1) - 10 (T1)
    HEAD
    Below 1 Ω
    13 (B1) - 10 (T1)
    TAIL
    13 (B1) - 10 (T1)
    OFF
    10 kΩ or higher

    RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (B1) - 8 (T1)
    HEAD
    Below 1 Ω
    5 (B1) - 8 (T1)
    TAIL
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY
OK


6.CHECK WIRE HARNESS (SWITCH - METER AND BATTERY)
E110290E06
  1. Disconnect the C10 switch connector.

  1. Disconnect the C8 meter connector.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    LHD 
    Tester Connection
    Specified Condition
    C10-13 (B1) - Body ground
    10 to 14 V

    RHD:
    Tester Connection
    Specified Condition
    C10-5 (B1) - Body ground
    10 to 14 V

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    C10-10 (T1) - C8-8
    Below 1 Ω

    RHD:
    Tester Connection
    Specified Condition
    C10-8 (T1) - C8-8
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER SIDE)
B111526E02
  1. Remove the courtesy light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed (OFF)
    Below 1 Ω
    Pushed (ON)
    10 kΩ or higher



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
OK


8.CHECK WIRE HARNESS (SWITCH - METER)
E110280E01
  1. Disconnect the D2 switch connector.

  1. Disconnect the C8 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D2-1 - C8-16
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY