ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE CYLINDER HEAD |
Remove the cylinder head (Click here).
| 2. REMOVE CYLINDER HEAD GASKET |
Remove the cylinder head gasket from the cylinder head.
| 3. REMOVE GENERATOR WITH VACUUM PUMP ASSEMBLY |
![]() |
Disconnect the terminal cap.
Remove the nut and generator wire.
Disconnect the generator connector.
![]() |
Remove the union bolt to disconnect the vacuum pump hose and remove the 2 gaskets.
Remove the union bolt to disconnect the vacuum pump oil inlet hose and remove the 2 gaskets.
Detach the vacuum pump oil inlet hose from the cord clip.
Disconnect the vacuum pump oil outlet hose.
![]() |
Remove the bolt and generator.
| 4. REMOVE INJECTION PUMP DRIVE PULLEY |
![]() |
Using SST, remove the pulley nut.
![]() |
Using SST, remove the drive pulley.
| 5. REMOVE INJECTION PUMP ASSEMBLY |
![]() |
Disconnect the engine speed sensor connector.
Disconnect the spill control valve connector.
Disconnect the correction unit connector.
Disconnect the timing control valve connector.
Disconnect the fuel temperature sensor connector.
Disconnect the engine wire clamp.
Disconnect the 3 fuel hoses.
![]() |
Remove the 3 bolts and injection pump stay.
Remove the 2 nuts and injection pump.
| 6. REMOVE OIL FILTER |
![]() |
Using SST, remove the oil filter.
| 7. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY |
![]() |
Remove the 10 bolts, 2 nuts, oil filter bracket and gasket.
| 8. REMOVE ENGINE OIL PRESSURE SWITCH |
Disconnect the oil pressure switch connector.
Using a 24 mm deep socket wrench, remove the oil pressure switch.
![]() |
Install the oil pressure gauge.
Warm up the engine.
Measure the oil pressure.
| Condition | Specified Condition |
| Idle | 29 kPa (0.3 kgf*cm2, 4.3 psi) or more |
| 3,000 rpm | 294 to 539 kPa (3.0 to 5.5 kgf*cm2, 43 to 78 psi) |
Remove the oil pressure gauge.
| 9. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH |
Remove the 4 bolts and mounting bracket.
| 10. REMOVE PUMP BRACKET |
Remove the 6 bolts and mounting bracket.
| 11. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
![]() |
Remove the 2 bolts (A and B).
Loosen the bolt (C), and remove the No. 1 timing belt idler.
| 12. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY |
Remove the bolt, No. 2 timing belt idler and spacer.
| 13. REMOVE WATER PUMP |
![]() |
Remove the 6 bolts, tension spring bracket, water pump and gasket.
| 14. REMOVE CRANKSHAFT TIMING PULLEY |
![]() |
Using SST, remove the timing pulley.
| 15. REMOVE OIL PAN SUB-ASSEMBLY |
Remove the 16 bolts and 2 nuts.
![]() |
Insert the blade of SST between the oil pan and cylinder block, and cut off applied sealer and remove the oil pan.
| 16. REMOVE OIL STRAINER SUB-ASSEMBLY |
Remove the 2 bolts, 2 nuts, oil strainer and gasket.
| 17. REMOVE TIMING GEAR CASE SUB-ASSEMBLY |
![]() |
Remove the 5 bolts, timing gear case and gasket.
| 18. REMOVE ENGINE REAR OIL SEAL RETAINER |
Remove the 4 bolts, oil seal retainer and gasket.
| 19. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 20. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.
Remove the 2 connecting rod cap nuts.
![]() |
Using a plastic hammer, lightly tap the connecting rod bolts and lift off the connecting rod cap.
![]() |
Cover the connecting rod bolts with a short piece of hose to protect the crankshaft from damage.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
If the crank pin or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
![]() |
Lay a strip of Plastigage across the crank pin.
Place the connecting rod cap on the connecting rod.
Match the numbered connecting rod cap with the connecting rod.
![]() |
Install the connecting rod cap with the front mark facing forward.
Install the connecting rod cap with the 2 nuts .
Apply alight of engine oil to the threads and under the heads of the connecting rod cap nuts.
![]() |
Install and alternately tighten the nuts of the connecting rod cap in several passes.
Mark the front of the connecting rod cap nuts with paint.
![]() |
Retighten the connecting rod cap nuts 90° as shown.
Check that the painted marks is now at a 90° angle to the front.
Remove the 2 nuts, connecting rod cap and lower bearing .
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| STD | 0.036 to 0.064 mm (0.0014 to 0.0025 in.) |
| U/S 0.25, U/S 0.50 | 0.033 to 0.079 mm (0.0013 to 0.0031 in.) |
![]() |
If using a standard bearing, replace it with one having the same number marked on the connecting rod cap. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.
| Mark | Specified Condition |
| 1 | 1.478 to 1.482 mm (0.0582 to 0.0583 in.) |
| 2 | 1.482 to 1.486 mm (0.0583 to 0.0585 in.) |
| 3 | 1.486 to 1.490 mm (0.0585 to 0.0587 in.) |
Completely remove the Plastigage.
| 21. REMOVE PISTON AND CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
![]() |
Cover the connecting rod bolts with a short piece of hose to protect the crankshaft from damage.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 22. REMOVE PISTON SUB-ASSEMBLY |
Check the fitting condition between the piston and piston pin.
![]() |
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin with a new piston and a set.
![]() |
Using a piston ring expander, remove the 2 compression rings.
Remove the oil ring and coil by hand.
Disconnect the connecting rod from the piston.
![]() |
Using snap ring pliers, remove the 2 snap rings from the piston.
![]() |
Gradually heat the piston to approx. 60°C (140°F).
![]() |
Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and pin and remove the connecting rod.
| 23. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| Item | Specified Condition |
| STD | 2.430 to 2.480 mm (0.0957 to 0.0976 in.) |
| O/S 0.125 | 2.493 to 2.543 mm (0.0981 to 0.1001 in.) |
| O/S 0.250 | 2.555 to 2.605 mm (0.1006 to 0.1026 in.) |
| 24. REMOVE CRANKSHAFT AND INSPECT OIL CLEARANCE |
![]() |
Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes, in the sequence shown.
![]() |
Using the removed crankshaft bearing cap bolts, pry the cap back and forth, and remove the crankshaft bearing caps, lower bearings and lower thrust washers (No. 3 crankshaft bearing cap only).
Clean each crankshaft journal and bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Install the 5 crankshaft bearing caps in their proper locations.
Install the crankshaft bearing cap bolts.
Apply a light coat of the engine oil to the threads and under the bolt heads of the crankshaft bearing caps.
![]() |
Install and uniformly tighten the 10 bolts of the crankshaft bearing caps, in several steps, in the sequence shown.
Remove the 10 bolts and 5 crankshaft bearing caps.
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| STD | 0.034 to 0.065 mm (0.0013 to 0.0026 in.) |
| U/S 0.25, U/S 0.50 | 0.033 to 0.079 mm (0.0013 to 0.0031 in.) |
![]() |
If using a standard bearing, replace it with one having the same number marked on the connecting rod cap. There are 3 sizes of standard bearings, marked 1, 2 and 3 accordingly.
| Mark | Specified Condition |
| 1 | 1.979 to 1.983 mm (0.0779 to 0.0781 in.) |
| 2 | 1.983 to 1.987 mm (0.0781 to 0.0782 in.) |
| 3 | 1.987 to 1.991 mm (0.0782 to 0.0784 in.) |
Completely remove the Plastigage.
Lift out the crankshaft.
| 25. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
Remove the 4 check valves and oil nozzles.
| 26. REMOVE CYLINDER BLOCK OIL ORIFICE |
Using a 6 mm hexagon wrench, remove the oil orifice.
| 27. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
Remove the water drain cock from the cylinder block.
| 28. REMOVE CRANKSHAFT POSITION SENSOR |
Remove the bolt and sensor.