Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM (for 2 Step Unlock Function)

POWER DOOR LOCK CONTROL SYSTEM (for 2 Step Unlock Function) > All Doors cannot be Locked / Unlocked Simultaneously

for Preparation Click here


DESCRIPTION

The integration relay drives the door lock motors according to switch signals from the door control switch of the power window regulator master switch and the driver side door key cylinder.
However, the driver side door key-linked lock / unlock function will not operate when the seat belt is fastened.

WIRING DIAGRAM


B183914E01


B181768E03


INSPECTION PROCEDURE

1.CHECK DOOR LOCK / UNLOCK OPERATION
  1. Proceed to the next step according to the system listed in the table below.

    Symptom
    Proceed to
    All doors cannot be locked / unlocked at once using door control switch on master switch (switch operation)
    A
    All doors cannot be locked / unlocked at once using door key cylinder on driver side (key operation)
    B
    Only one door cannot be locked / unlocked
    C
    All symptoms listed above are present
    D



B
Go to step 4

C
Go to step 7

D
Go to step 13
A


2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)
B122670E01
  1. Measure the resistance of the door control switch.

    Standard resistance:
    Double Cab (w/o Jam Protection Function):
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 5
    Lock
    Below 1 Ω
    3 - 5, 3 - 8
    OFF
    10 kΩ or higher
    3 - 8
    Unlock
    Below 1 Ω
    Double Cab (w/ Jam Protection Function):
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 5
    Lock
    Below 1 Ω
    1 - 5, 1 - 8
    OFF
    10 kΩ or higher
    1 - 8
    Unlock
    Below 1 Ω
    Single Cab:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 10
    Lock
    Below 1 Ω
    3 - 10, 4- 10
    OFF
    10 kΩ or higher
    4 - 10
    Unlock
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


3.CHECK WIRE HARNESS (MASTER SWITCH - INTEGRATION RELAY AND BODY GROUND)
B112006E05
  1. Disconnect the P4 switch connector.

  1. Disconnect the 2A and 2D integration relay connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Double Cab (w/o Jam Protection Function):
    Tester Connection
    Specified Condition
    P4-5 - 2A-4 (L1)
    Below 1 Ω
    P4-8 - 2D-4 (UL1)
    Below 1 Ω
    P4-3 - Body ground
    Below 1 Ω
    P4-5 or 2A-4 (L1) - Body ground
    10 kΩ or higher
    P4-8 or 2D-4 (UL1) - Body ground
    10 kΩ or higher
    Double Cab (w/ Jam Protection Function):
    Tester Connection
    Specified Condition
    P4-5 - 2A-4 (L1)
    Below 1 Ω
    P4-8 - 2D-4 (UL1)
    Below 1 Ω
    P4-1 - Body ground
    Below 1 Ω
    P4-5 or 2A-4 (L1) - Body ground
    10 kΩ or higher
    P4-8 or 2D-4 (UL1) - Body ground
    10 kΩ or higher
    Single Cab:
    Tester Connection
    Specified Condition
    P4-3 - 2A-4 (L1)
    Below 1 Ω
    P4-4 - 2D-4 (UL1)
    Below 1 Ω
    P4-10 - Body ground
    Below 1 Ω
    P4-3 or 2A-4 (L1) - Body ground
    10 kΩ or higher
    P4-4 or 2D-4 (UL1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY 

4.INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE DOOR LOCK AND UNLOCK SWITCH)
B065430E12
  1. Measure the resistance of the door lock and unlock switch.

    Standard resistance:
    Tester Connection
    Door Lock Condition
    Specified Condition
    6 - 8
    Lock
    Below 1 Ω
    5 - 8, 6- 8
    OFF
    10 kΩ or higher
    5 - 8
    Unlock
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)
OK


5.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
B085672E10
  1. Measure the resistance of the buckle switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt is unfastened
    Below 1 Ω
    1 - 2
    Seat belt is fastened
    1 MΩ or higher



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
OK


6.CHECK WIRE HARNESS (DRIVER SIDE DOOR LOCK - INTEGRATION RELAY AND BODY GROUND)
B118172E04
  1. Disconnect the D6 door lock connector.

  1. Disconnect the 2A and 2D integration relay connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-5 - 2D-4 (UL1)
    Always
    Below 1 Ω
    D6-6 - 2A-4 (L1)
    Always
    Below 1 Ω
    D6-8 - Body ground
    Driver seat belt is not fastened
    Below 1 Ω
    D6-5 or 2D-4 (UL1) - Body ground
    Always
    10 kΩ or higher
    D6-6 or 2A-4 (L1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY 

7.CHOOSE SYMPTOM
  1. Proceed to the next step according to the system listed in the table below.


Symptom
Proceed to
Passenger door, rear door LH or rear door RH cannot be locked/unlocked
A
Driver door cannot be locked/unlocked
B


B
Go to step 10
A


8.INSPECT DOOR LOCK ASSEMBLY (PASSENGER SIDE, REAR LH AND REAR RH)

B118170E01

  1. Apply battery voltage to the door lock and check the operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock



NG
REPLACE DOOR LOCK ASSEMBLY
OK


9.CHECK WIRE HARNESS (DOOR LOCK - INTEGRATION RELAY AND BODY GROUND)
B111993E02
  1. Disconnect the D7, D8* and D9* door lock connectors.

  1. Disconnect the 2K and 2R integration relay connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D7-4 - 2K-11 (ACT+)
    Below 1 Ω
    D7-1 - 2K-10 (ACT-)
    Below 1 Ω
    D8-4 - 2K-11 (ACT+)*
    Below 1 Ω
    D8-1 - 2K-10 (ACT-)*
    Below 1 Ω
    D9-4 - 2R-28 (ACT+)*
    Below 1 Ω
    D9-1 - 2R-27 (ACT-)*
    Below 1 Ω
    D7-4 or 2K-11 (ACT+) - Body ground
    10 kΩ or higher
    D7-1 or 2K-10 (ACT-) - Body ground
    10 kΩ or higher
    D8-4 or 2K-11 (ACT+) - Body ground*
    10 kΩ or higher
    D8-1 or 2K-10 (ACT-) - Body ground*
    10 kΩ or higher
    D9-4 or 2R-28 (ACT+) - Body ground*
    10 kΩ or higher
    D9-1 or 2R-27 (ACT-) - Body ground*
    10 kΩ or higher

    HINT:
    *: Double Cab



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY 

10.INSPECT DOOR LOCK (DRIVER SIDE)
B065429E14
  1. Apply battery voltage to the door lock and check the operation of the door lock motor.

OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Lock
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Unlock



NG
REPLACE DOOR LOCK ASSEMBLY
OK


11.CHECK WIRE HARNESS (DOOR LOCK - INTEGRATION RELAY)
B118162E02
  1. Disconnect the D6 door lock connector.

  1. Disconnect the 2R integration relay connector.

  1. Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection
Specified Condition
D6-4 - 2R-28 (ACT+)
Below 1 Ω
D6- 4 or 2R-28 (ACT+) - Body ground
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


12.CHECK WIRE HARNESS (DOOR LOCK - THEFT WARNING ECU)
B118163E02
  1. Disconnect the D6 door lock connector.

  1. Disconnect the T16 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection
Specified Condition
D6-1 - T16-11 (DDUL)
Below 1 Ω
T16-1 (E) - Body ground
Below 1 Ω
D6-1 or T16-11 (DDUL) - Body ground
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE THEFT WARNING ECU 

13.INSPECT FUSE (ECU-B, DCC, DOOR)
  1. Remove the ECU-B and DCC fuses from the engine room relay block.

  1. Remove the DOOR fuse from the No. 3 relay block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


14.CHECK WIRE HARNESS (INTEGRATION RELAY - BATTERY AND BODY GROUND)
B111994E01
  1. Disconnect the 2D, 2H and 2L integration relay connectors.

  1. Measure the voltage and resistance of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    2L-12 (BECU) - Body ground
    10 to 14 V
    2H-4 (ALTB) - Body ground
    10 to 14 V

    Standard resistance:
    Tester Connection
    Specified Condition
    2D-9 (GND) - Body ground
    Below 1 Ω
    2D-18 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


15.CHECK WIRE HARNESS (MASTER SWITCH - INTEGRATION RELAY AND BODY GROUND)
B112006E06
  1. Disconnect the P4 switch connector.

  1. Disconnect the 2A and 2D integration relay connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Double Cab (w/o Jam Protection Function):
    Tester Connection
    Specified Condition
    P4-5 - 2A-4 (L1)
    Below 1 Ω
    P4-8 - 2D-4 (UL1)
    Below 1 Ω
    P4-3 - Body ground
    Below 1 Ω
    P4-5 or 2A-4 (L1) - Body ground
    10 kΩ or higher
    P4-8 or 2D-4 (UL1) - Body ground
    10 kΩ or higher
    Double Cab (w/ Jam Protection Function):
    Tester Connection
    Specified Condition
    P4-5 - 2A-4 (L1)
    Below 1 Ω
    P4-8 - 2D-4 (UL1)
    Below 1 Ω
    P4-1 - Body ground
    Below 1 Ω
    P4-5 or 2A-4 (L1) - Body ground
    10 kΩ or higher
    P4-8 or 2D-4 (UL1) - Body ground
    10 kΩ or higher
    Single Cab:
    Tester Connection
    Specified Condition
    P4-3 - 2A-4 (L1)
    Below 1 Ω
    P4-4 - 2D-4 (UL1)
    Below 1 Ω
    P4-10 - Body ground
    Below 1 Ω
    P4-3 or 2A-4 (L1) - Body ground
    10 kΩ or higher
    P4-4 or 2D-4 (UL1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY