Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/o EGR Cooler)

DTC    P0093/78    Fuel System Leak Detected - Large Leak

for Preparation Click here


DESCRIPTION

HINT:
  1. If DTC P1229/78 is set, P0093/78 (fuel leaks in high-pressure areas) may be set simultaneously. This may be due to extremely high internal fuel pressure in the common rail causing the pressure limiter to open. The ECM is interpreting this as a fault and setting P0093/78.
  2. For more information on the common rail system, refer to the system description (Click here).
  3. If P0093/78 is present, refer to the "Diagnostic Trouble Code (DTC) Table for Common Rail System" (Click here).

Refer to the system description (Click here).

DTC No.
DTC Detection Condition
Trouble Area
P0093/78
Fuel leaks in high-pressure areas
(1 trip detection logic)
  1. Fuel line between supply pump and common rail
  2. Fuel line between common rail and each injector
  3. Supply pump
  4. Common rail
  5. Injectors
  6. Pressure limiter
  7. Open or short in EDU circuit (P0200/97 set simultaneously)
  8. Open or short in injector circuit
  9. EDU (P0200/97 set simultaneously)
  10. ECM

HINT:
When DTC P0093/78 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Fuel Press.


Reference:

Engine Speed
Fuel Pressure
Idling
Approximately 25000 to 35000 kPa
3,000 rpm (No engine load)
Approximately 35000 to 55000 kPa


MONITOR DESCRIPTION

P0093/78 (Fuel leaks in high-pressure areas):
  1. This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM sets this DTC if the drop in the internal fuel pressure is large when injecting fuel.
    In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the supply pump, common rail, injectors and piping. The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.
    If this DTC is set, the ECM enters fail-safe mode. Fail-safe mode suspends both fuel injection and supply pump operation, and then stops the engine. Before stopping the engine, the ECM permits the vehicle to be driven for 1 minute. Fail-safe mode continues until the ignition switch is turned OFF.

MONITOR STRATEGY


Required sensors
Fuel pressure sensor
Frequency of operation
Continuous
Duration
1 second
MIL operation
1 driving cycle

TYPICAL ENABLING CONDITIONS


Item
Specification
Minimum
Specification
Maximum
Engine speed
600 rpm
-
The monitor will not run if the fuel pressure sensor or suction control valve circuit is malfunctioning

TYPICAL MALFUNCTION THRESHOLDS


Threshold
Drop of the internal fuel pressure is large when injecting fuel

INSPECTION PROCEDURE

NOTICE:
  1. Soon after starting the engine, visually check for fuel leaks in the fuel line.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  4. After replacing a fuel injector, the ECM needs registration (Click here).


When using intelligent tester:

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
  1. Before starting the engine, visually check for fuel leaks from the fuel supply pump, fuel injectors, common rail, and the fuel pipes in high-pressure areas.

    OK:
    No fuel leaks in high-pressure areas.



NG
REPAIR FUEL LEAK POINT
OK


2.CHECK FOR ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P0093/78)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0093/78
    A
    P0093/78 and other Current DTCs
    B



B
GO TO DTC CHART
A


3.CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Record the stored DTC and Freeze Frame Data.

    HINT:
    Check the values, especially the following Freeze Frame Data items, and write them down.


    Tester Display
    (Freeze Frame Data Item)
    Measurement Item
    Standard
    (Reference)
    Target Pump SCV Current
    Target current value flowing to the SCV of the fuel supply pump
    800 to 3000 mA
    Fuel Press
    Actual fuel pressure inside the common rail
    1. 25000 to 35000 kPa when idling
    2. 35000 to 55000 kPa when engine speed maintained at 3000 rpm with no load
    Injection Feedback Val #1
    Injection Feedback Val #2
    Injection Feedback Val #3
    Injection Feedback Val #4
    Injection volume correction value for each cylinder
    Between -4.9 mm3/st and 4.9 mm3/st


NEXT


4.CHECK FREEZE FRAME DATA (TARGET PUMP SCV CURRENT)
  1. Turn the tester ON.

  1. Read the value of Target Pump SCV Current recorded in the Freeze Frame Data.

    Standard:
    Tester Display
    Specified Condition
    Target Pump SCV Current
    800 to 3000 mA

    HINT:
    If the value is higher than the standard, confirm the following engine conditions from when the DTC was stored.
    1. The time the ignition switch was turned from ON to START was not extremely short.
    2. The battery was not depleted, and the battery terminals were not loose or corroded.



NG
Go to step 47
OK


5.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
  1. Check if the fuel level is low.

    Result:
    Result
    Proceed to
    The indicator (fuel warning light) is illuminated
    A
    The indicator (fuel warning light) is not illuminated
    B



B
Go to step 8
A


6.ADD FUEL

NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093/78)


    A194856
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Repeat steps (*A) to (*D).

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Confirm that the shift lever is in neutral, and securely apply the parking brake.

  1. Fully depress the accelerator pedal for 5 seconds and then release it. (*E)

  1. Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)



  1. Repeat the above procedures (*E) and (*F) 5 times.


    A196453E01

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    DTC output
    A
    DTC not output
    B



B
DTC CAUSED BY RUNNING OUT OF FUEL
A


8.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
  1. Turn the tester ON.

  1. Read the value of Injection Feedback Val #1 to #4 recorded in the Freeze Frame Data.

    Result:
    Result
    Proceed to
    -4.9 to 4.9 mm3/st
    A
    -5 mm3/st or 5 mm3/st
    B



B
Go to step 25
A


9.CHECK ENGINE STARTING CONDITION
  1. Check whether the engine can be started within 4 seconds.

OK:
The engine can be started within 4 seconds.



NG
Go to step 41
OK


10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.



    A176220E02
  1. Take a snapshot with the intelligent tester during the Active Test.

    HINT:
    Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.



  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the Active Test / Test the Fuel Leak is performed (Click here).

    HINT:
    To be fine measurements, perform the Active Test with measurements 5 times or more.


    A190323E05

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 15000 kPa.

    HINT:
    1. "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
    2. "Fuel Press" is the actual fuel pressure.
    3. If the pressure limiter mounted on the common rail is malfunctioning, the actual fuel pressure will change as shown by the line labeled "Pressure Limiter Malfunctioning" in the illustration.
    4. Under normal conditions, the pressure limiter opens and releases abnormally high pressure to the return pipe when the fuel pressure inside the common rail reaches 180000 kPa. If the actual fuel pressure suddenly drops to 40000 to 50000 kPa even though the fuel pressure inside the common rail does not reach 180000 kPa, replace the common rail assembly because the pressure at which the pressure limiter opens can be assumed to be too low.

  1. Read the value of Target Pump SCV Current in the Data List when the Active Test / Test the Fuel Leak is performed.

    Standard:
    Target Pump SCV Current is between 800 mA and 3000 mA.

    HINT:
    If the value of Target Pump SCV Current stored in the Freeze Frame Data is higher than the standard, intermittent sticking of the suction control valve may be the cause of the malfunction.


    Result:

    Result
    Proceed to
    Difference between target fuel pressure and actual fuel pressure is 15000 kPa or more
    B
    Target Pump SCV Current value is out of standard range
    C
    Both results are within standard range
    A



B
Go to step 37

C
Go to step 47
A


11.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / Data List / Fuel Temperature.

  1. Read the value.

    OK:
    The value is almost the same as the actual fuel temperature.

    HINT:
    When the engine is stopped and left overnight, the fuel temperature becomes the same as the atmospheric temperature.



NG
Go to step 56
OK


12.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / Data List / Engine Speed.

  1. Read the value while cranking and idling the engine.

    Standard:
    Tester Display
    Engine Condition
    Specified Condition
    Engine Speed
    Cranking
    50 to 400 rpm
    Idling with warm engine
    700 to 800 rpm

    HINT:
    The value should be the same as the actual engine speed and displayed with no interruption on the tester.



NG
Go to step 57
OK


13.INSPECT CAMSHAFT POSITION SENSOR (SENSOR RESISTANCE)


    A064984
  1. Disconnect the camshaft position sensor connector.

  1. Measure the sensor resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Approx. 20°C (68°F)
    950 to 1250 Ω

  1. Reconnect the sensor connector.



NG
Go to step 58
OK


14.INSPECT HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Check for an open or short circuit in the wire harness and connectors between the ECM and camshaft position sensor.

    OK:
    The wire harness and connectors do not have any open or short circuits, or corrosion.

  1. Reconnect the ECM and sensor connectors.



NG
Go to step 59
OK


15.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
  1. Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.

  1. Turn the ignition switch to ON.



  1. Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


    A192850E03


    A192849E02

    OK:
    No noise in the waveform.


    Result:

    Result
    Proceed to
    MIL comes on or noise exists in the waveform
    B
    Except above
    A



B
Go to step 51
A


16.CHECK ENGINE OIL CONDITION
  1. Remove the oil filler cap (and the engine oil level dipstick), and check whether the engine oil smells of diesel fuel.

    OK:
    The engine oil does not smell of diesel fuel.



NG
Go to step 18
OK


17.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).



NEXT
Go to step 60

18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL CUT FOR IDENTIFYING MALFUNCTION)

HINT:
Perform the Active Test below to identify the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.

  1. Check the four cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.

    HINT:
    1. While the engine is idling, if the idling stability variation is small despite cutting off the fuel injection, the cylinder is malfunctioning.
    2. With normal cylinders, the engine idles roughly when fuel injection is cut off.

    Result:
    Result
    Proceed to
    Malfunctioning cylinder not confirmed
    A
    Malfunctioning cylinder confirmed
    B



B
Go to step 21
A


19.CHANGE ENGINE OIL
  1. Remove the oil pan drain plug and drain the engine oil.

  1. Install the oil pan drain plug.

  1. Remove the oil filler cap.

  1. Add fresh oil and install the oil filler cap.

    HINT:
    Check the engine oil level after changing the engine oil. The engine oil level should be between the LOW and FULL marks.


NEXT


20.CHECK FOR INTERMITTENT PROBLEMS
  1. Check for intermittent problems (Click here).



NEXT
Go to step 60

21.REPLACE FUEL INJECTOR (FUEL INJECTOR OF MALFUNCTIONING CYLINDER)
  1. Replace the fuel injectors of the malfunctioning cylinders.


NEXT


22.REGISTER INJECTOR COMPENSATION CODE
  1. Register the injector compensation code (Click here).


NEXT


23.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).


NEXT


24.CHANGE ENGINE OIL
  1. Remove the oil pan drain plug and drain the engine oil.

  1. Install the oil pan drain plug.

  1. Remove the oil filler cap.

  1. Add fresh oil and install the oil filler cap.

    HINT:
    Check the engine oil level after changing the engine oil. The engine oil level should be between the LOW and FULL marks.



NEXT
Go to step 60

25.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Clear DTCs.


NEXT


26.CHECK ENGINE START CONDITION
  1. Check whether the engine can be started within 4 seconds.

OK:
The engine can be started within 4 seconds.



OK
Go to step 31

NG
Go to step 27

27.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).


NEXT


28.CHECK ENGINE START CONDITION
  1. Check whether the engine can be started.

    OK:
    The engine can be started.



OK
Go to step 31

NG
Go to step 29

29.CHECK AND REPLACE FUEL INLET LINE
  1. Check the following items, and repair or replace the malfunctioning part if necessary.

    1. Check for fuel filter clogging.

    2. Check for fuel freezing in the fuel line.

    3. Check for clogging or leaks in the fuel pipe and hose between the fuel tank and fuel supply pump.


NEXT


30.CHECK ENGINE START CONDITION
  1. Check whether the engine can be started.

    OK:
    The engine can be started.



NG
Go to step 37
OK


31.READ VALUE USING INTELLIGENT TESTER (INJECTION VALUE FEEDBACK VAL #1 TO #4)

HINT:
  1. Perform the procedures below to identify the malfunctioning cylinder.
  2. The cylinder that has an Injection Feedback Val of -5 mm3/st or 5 mm3/st is the cylinder suspected to be malfunctioning.

  1. Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher.

  1. Allow the engine to idle for 1 minute or more.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / Data List / Target Pump SCV Current and Injector Feedback Val. #1 to #4 (Click here).



    A176220E02
  1. Take a snapshot with the intelligent tester.

    HINT:
    Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.

  1. Read the values.

    Standard:

    Tester Display
    Engine Condition
    Specified Condition
    Injection Feedback Val #1
    Injection Feedback Val #2
    Injection Feedback Val #3
    Injection Feedback Val #4
    Idling
    Between -4.9 mm3/st and 4.9 mm3/st
    Target Pump SCV Current
    Idling and revving engine to 3000 rpm 5 times
    800 to 3000 mA

    HINT:
    1. The shift lever should be in neutral, and the A/C switch and all accessory switches should be off.
    2. If the value of Target Pump SCV Current is higher than the standard, intermittent sticking of the suction control valve may be the cause of the malfunction. Under normal conditions, the value is about 2000 mA or less.


    Result:

    Result
    Proceed to
    Target Pump SCV Current value is out of standard range
    B
    Except above
    A



B
Go to step 47
A


32.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL CUT FOR IDENTIFYING MALFUNCTION)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.

  1. Check the four cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.

    HINT:
    1. While the engine is idling, if the idling stability variation is small despite cutting off the fuel injection, the cylinder is malfunctioning.
    2. With normal cylinders, the engine idles roughly when the fuel injection is cut off.


NEXT


33.REPLACE FUEL INJECTOR (FUEL INJECTOR OF MALFUNCTIONING CYLINDER)
  1. Replace the fuel injectors of the malfunctioning cylinders.

    HINT:
    If it was difficult to determine the malfunctioning cylinders when performing the Active Test above, replace all fuel injectors.


NEXT


34.REGISTER INJECTOR COMPENSATION CODE
  1. Register the injection compensation code (Click here).


NEXT


35.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).


NEXT


36.CHANGE ENGINE OIL
  1. Remove the oil pan drain plug and drain the engine oil.

  1. Install the oil pan drain plug.

  1. Remove the oil filler cap.

  1. Add fresh oil and install the oil filler cap.

    HINT:
    Check the engine oil level after changing the engine oil. The engine oil level should be between the LOW and FULL marks.



NEXT
Go to step 60

37.REPLACE SUPPLY PUMP
  1. Replace the supply pump.


NEXT


38.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).


NEXT


39.PERFORM SUPPLY PUMP INITIALIZATION
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Clear DTCs.

  1. Perform supply pump initialization (Click here).


NEXT


40.CHECK ENGINE START CONDITION
  1. Check whether the engine can be started.

    OK:
    The engine can be started.



OK
Go to step 31

NG
Go to step 45

41.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).


NEXT


42.CHECK ENGINE START CONDITION
  1. Check whether the engine can be started.

    OK:
    The engine can be started.



OK
Go to step 10

NG
Go to step 43

43.CHECK AND REPLACE FUEL INLET LINE
  1. Check the following items, and repair or replace the malfunctioning part if necessary.

    1. Check for fuel filter clogging.

    2. Check for fuel freezing in the fuel line.

    3. Check for clogging or leaks in the fuel pipe and hose between the fuel tank and fuel supply pump.


NEXT


44.CHECK ENGINE START CONDITION
  1. Check whether the engine can be started.

    OK:
    The engine can be started.



OK
Go to step 10

NG
Go to step 37

45.REPLACE COMMON RAIL ASSEMBLY
  1. Replace the common rail assembly.


NEXT


46.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).



NEXT
Go to step 31

47.CHECK HARNESS AND CONNECTOR (ECM - SUCTION CONTROL VALVE)
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Check for an open or short circuit in the wire harness and connectors between the ECM and suction control valve.

    OK:
    The wire harness and connectors do not have any open or short circuits.

  1. Reconnect the ECM and suction control valve connectors.



OK
Go to step 49

NG
Go to step 48

48.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - SUCTION CONTROL VALVE)
  1. Repair or replace the harness or connector.



NEXT
Go to step 55

49.REPLACE SUPPLY PUMP
  1. Replace the supply pump.


NEXT


50.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).



NEXT
Go to step 55

51.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
  1. Repair or replace the harness or connector.


NEXT


52.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
  1. Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.

  1. Turn the ignition switch to ON.



  1. Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


    A192850E03


    A192849E02

    OK:
    No noise in the waveform.


    Result:

    Result
    Proceed to
    MIL comes on or noise exists in the waveform
    B
    Except above
    A



B
Go to step 60
A


53.REPLACE COMMON RAIL ASSEMBLY
  1. Replace the common rail assembly.


NEXT


54.BLEED AIR FROM FUEL SYSTEM
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.

    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Clear DTCs.

  1. Start the engine. (*A)

  1. Enter the following menus: Powertrain / Pick Up / Engine / Active Test / Test the Fuel Leak. (*B)

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)


    A192848E03

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear DTCs.

  1. Repeat steps (*A) to (*D).


NEXT


55.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Clear DTCs.

  1. Perform supply pump initialization (Click here).



NEXT
Go to step 60

56.REPLACE FUEL TEMPERATURE SENSOR
  1. Replace the fuel temperature sensor.



NEXT
Go to step 60

57.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor.



NEXT
Go to step 60

58.REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor.



NEXT
Go to step 60

59.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)
  1. Repair or replace the harness or connector.


NEXT


60.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093/78)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Pick Up / Engine / DTC.

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Confirm that the shift lever is in neutral, and securely apply the parking brake.

  1. Fully depress the accelerator pedal for 5 seconds and then release it. (*A)

  1. Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)



  1. Repeat the above procedures (*A) and (*B) 5 times.


    A196453E04

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    OK:
    No DTCs are output.


NEXT

END 


When not using intelligent tester:

1.CHECK DTC OUTPUT
  1. Turn the ignition switch ON.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    P0093/78 only
    A
    P0093/78 and P0200/97
    B



B
GO TO RELEVANT DTC CHART
A


2.CHECK FOR FUEL LEAK
  1. Visually check the supply pump, each injector, and the fuel line located between the supply pump and common rail for fuel leaks or fuel pressure leaks. Also, perform the same check on the fuel line between the common rail and each injector.

    OK:
    No leakage.

    HINT:
    There is a possibility that fuel leaks inside the components (supply pump, etc.) have occurred.



NG
REPAIR OR REPLACE
OK

REPLACE INJECTOR ASSEMBLY