AUTOMATIC TRANSMISSION SYSTEM > Park / Neutral Position Switch Circuit |

| Item | Measurement Item/ Range (Display) | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever is: On P or N: ON Not on P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever is: On R: ON Not on R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (D or 3 Range) | PNP switch status/ ON or OFF | Shift lever is: On D or 3: ON Not on D or 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (2 Range) | PNP switch status/ ON or OFF | Shift lever is: On 2: ON Not on 2: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW status (L Range) | PNP switch status/ ON or OFF | Shift lever is: On L: ON Not on L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| 1.INSPECT PARK/NEUTRAL POSITION SWITCH*1 |
![]() |
Disconnect the N1 park/neutral position switch connector.
Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| 4 (B) - 5 (L) | P or N | Below 1 Ω |
| 4 (B) - 5 (L) | Not on P or N | 10 kΩ or higher |
| 1 (RL) - 2 (RB) | R | Below 1 Ω |
| 1 (RL) - 2 (RB) | Not on R | 10 kΩ or higher |
| 2 (RB) - 7 (DL) | D | Below 1 Ω |
| 2 (RB) - 7 (DL) | Not on D | 10 kΩ or higher |
| 2 (RB) - 3 (2L) | 2 | Below 1 Ω |
| 2 (RB) - 3 (2L) | Not on 2 | 10 kΩ or higher |
| 2 (RB) - 8 (LL) | L | Below 1 Ω |
| 2 (RB) - 8 (LL) | Not on L | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT SHIFT LOCK CONTROL ECU*2 |
![]() |
Disconnect the S11 ECU connector.
Measure the resistance of the ECU when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| 9 (NSSD) - 3 (AT3) | D | 10 kΩor higher |
| 9 (NSSD) - 3 (AT3) | 3 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK WIRE HARNESS (TCM - BATTERY) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the wire harness side connectors.
| Tester Connection | Shift Lever Position | Specified Condition |
| T18-9 (R) - Body ground | R | 10 to 14 V* |
| T18-9 (R) - Body ground | Not on R | Below 1 V |
| T18-8 (D) - Body ground | D or 3 | 10 to 14 V |
| T18-8 (D) - Body ground | Not on D or 3 | Below 1 V |
| T18-12 (3) - Body ground | 3 | 10 to 14 V |
| T18-12 (3) - Body ground | Not on 3 | Below 1 V |
| T18-11 (2) - Body ground | 2 | 10 to 14 V |
| T18-11 (2) - Body ground | Not on 2 | Below 1 V |
| T18-10 (L) - Body ground | L | 10 to 14 V |
| T18-10 (L) - Body ground | Not on L | Below 1 V |
|
| ||||
| OK | ||
| ||